 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CY7C63722C CY7C63723C CY7C63743C enCoReTM USB Combination Low-Speed USB and PS/2 Peripheral Controller Features Internal low-power wake-up timer during suspend mode Periodic wake-up with no external components Optional 6-MHz internal oscillator mode Allows fast start-up from suspend mode Watchdog Reset (WDR) Low-voltage Reset at 3.75V Internal brown-out reset for suspend mode Improved output drivers to reduce EMI Operating voltage from 4.0V to 5.5VDC Operating temperature from 0C to 70C CY7C63723C available in 18-pin SOIC, 18-pin PDIP CY7C63743C available in 24-pin SOIC, 24-pin PDIP, 24-pin QSOP CY7C63722C available in DIE form Industry standard programmer support de en Cypress Semiconductor Corporation Document #: 38-08022 Rev. *D N ot R I/O ports Up to 16 versatile GPIO pins, individually configurable High current drive on any GPIO pin: 50 mA/pin current sink Each GPIO pin supports high-impedance inputs, internal pull-ups, open drain outputs or traditional CMOS outputs Maskable interrupts on all I/O pins ec om m * 198 Champion Court d 8-bit RISC microcontroller Harvard architecture 6-MHz external ceramic resonator or internal clock mode 12-MHz internal CPU clock Internal memory 256 bytes of RAM 8 Kbytes of EPROM Interface can auto-configure to operate as PS/2 or USB No external components for switching between PS/2 and USB modes No GPIO pins needed to manage dual mode capability fo USB Specification Compliance Conforms to USB Specification, Version 2.0 Conforms to USB HID Specification, Version 1.1 Supports one low-speed USB device address and three data endpoints Integrated USB transceiver 3.3V regulated output for USB pull-up resistor rN ew * Flexible, cost-effective solution for applications that combine PS/2 and low-speed USB, such as mice, gamepads, joysticks, and many others. San Jose, CA 95134-1709 * 408-943-2600 Revised October 20, 2010 [+] Feedback D es enCoReTM USB - enhanced Component Reduction Internal oscillator eliminates the need for an external crystal or resonator Interface can auto-configure to operate as PS/2 or USB without the need for external components to switch between modes (no General Purpose I/O [GPIO] pins needed to manage dual mode capability) Internal 3.3V regulator for USB pull-up resistor Configurable GPIO for real-world interface without external components SPI serial communication block Master or slave operation 2 Mbit/s transfers Four 8-bit Input Capture registers Two registers each for two input pins Capture timer setting with five prescaler settings Separate registers for rising and falling edge capture Simplifies interface to RF inputs for wireless applications ig ns CY7C63722C CY7C63723C CY7C63743C Logic Block Diagram XTALIN/P2.1 XTALOUT Brown-out Reset Watch Dog Timer Low Voltage Reset Interrupt Controller USB Engine USB & PS/2 Xcvr Port 1 GPIO 3.3V Regulator fo VREG/P2.0 D+,D- enCoRe USB--The New USB Standard The CY7C637xxC features up to 16 GPIO pins to support USB, PS/2 and other applications. The I/O pins are grouped into two ports (Port 0 to 1) where each pin can be individually configured as inputs with internal pull-ups, open drain outputs, or traditional CMOS outputs with programmable drive strength of up to 50 mA output drive. Additionally, each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Note the GPIO interrupts all share the same "GPIO" interrupt vector. The CY7C637xxC microcontrollers feature an internal oscillator. With the presence of USB traffic, the internal oscillator can be set to precisely tune to USB timing requirements (6 MHz 1.5%). Document #: 38-08022 Rev. *D N The CY7C637xxC is an 8-bit RISC one-time-programmable (OTP) microcontroller. The instruction set has been optimized specifically for USB and PS/2 operations, although the microcontrollers can be used for a variety of other embedded applications. ot R Cypress has reinvented its leadership position in the low-speed USB market with a new family of innovative microcontrollers. Introducing...enCoRe USB--"enhanced Component Reduction." Cypress has leveraged its design expertise in USB solutions to create a new family of low-speed USB microcontrollers that enables peripheral developers to design new products with a minimum number of components. At the heart of the enCoRe USB technology is the breakthrough design of a crystalless oscillator. By integrating the oscillator into our chip, an external crystal or resonator is no longer needed. We have also integrated other external components commonly found in low-speed USB applications such as pull-up resistors, wake-up circuitry, and a 3.3V regulator. All of this adds up to a lower system cost. en de ec om m d Functional Overview Optionally, an external 6-MHz ceramic resonator can be used to provide a higher precision reference for USB operation. This clock generator reduces the clock-related noise emissions (EMI). The clock generator provides the 6- and 12-MHz clocks that remain internal to the microcontroller. The CY7C637xxC has 8 Kbytes of EPROM and 256 bytes of data RAM for stack space, user variables, and USB FIFOs. These parts include low-voltage reset logic, a Watchdog timer, a vectored interrupt controller, a 12-bit free-running timer, and capture timers. The low-voltage reset (LVR) logic detects when power is applied to the device, resets the logic to a known state, and begins executing instructions at EPROM address 0x0000. LVR will also reset the part when VCC drops below the operating voltage range. The Watchdog timer can be used to ensure the firmware never gets stalled for more than approximately 8 ms. The microcontroller supports 10 maskable interrupts in the vectored interrupt controller. Interrupt sources include the USB Bus-Reset, the 128-s and 1.024-ms outputs from the free-running timer, three USB endpoints, two capture timers, an internal wake-up timer and the GPIO ports. The timers bits cause periodic interrupts when enabled. The USB endpoints interrupt after USB transactions complete on the bus. The capture timers interrupt whenever a new timer value is saved due to a selected GPIO edge event. The GPIO ports have a level of masking to select which GPIO inputs can cause a GPIO interrupt. For additional flexibility, the input transition polarity that causes an interrupt is programmable for each GPIO pin. The interrupt polarity can be either rising or falling edge. The free-running 12-bit timer clocked at 1 MHz provides two interrupt sources as noted above (128 s and 1.024 ms). The timer can be used to measure the duration of an event under firmware control by reading the timer at the start and end of an Page 2 of 53 rN ew P1.0-P1.7 P0.0-P0.7 D es Port 0 GPIO [+] Feedback EPROM 8K Byte 8-bit RISC Core ig ns Internal Oscillator Xtal Oscillator Wake-Up Timer RAM 256 Byte 12-bit Timer Capture Timers SPI CY7C63722C CY7C63723C CY7C63743C event, and subtracting the two values. The four capture timers save a programmable 8 bit range of the free-running timer when a GPIO edge occurs on the two capture pins (P0.0, P0.1). The CY7C637xxC includes an integrated USB serial interface engine (SIE) that supports the integrated peripherals. The hardware supports one USB device address with three endpoints. The SIE allows the USB host to communicate with the function integrated into the microcontroller. A 3.3V regulated output pin provides a pull-up source for the external USB resistor on the D- pin. The USB D+ and D- USB pins can alternately be used as PS/2 SCLK and SDATA signals, so that products can be designed to respond to either USB or PS/2 modes of operation. PS/2 operation is supported with internal pull-up resistors on SCLK and SDATA, the ability to disable the regulator output pin, and an interrupt to signal the start of PS/2 activity. No external components are necessary for dual USB and PS/2 systems, and no GPIO pins need to be dedicated to switching between modes. Slow edge rates operate in both modes to reduce EMI. CY7C63723C 18-pin SOIC/PDIP P0.0 P0.1 P0.2 P0.3 P1.0 VSS VPP VREG/P2.0 XTALIN/P2.1 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 P0.4 P0.5 P0.6 P0.7 P1.1 D+/SCLK D-/SDATA VCC XTALOUT CY7C63743C 24-pin SOIC/PDIP/QSOP P0.0 P0.1 P0.2 P0.3 P1.0 P1.2 P1.4 P1.6 VSS VPP VREG/P2.0 XTALIN/P2.1 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 P0.4 P0.5 P0.6 P0.7 P1.1 P1.3 P1.5 P1.7 D+/SCLK D-/SDATA VCC XTALOUT rN ew Voltage supply Ground P0.3 P1.0 P1.2 P1.4 P1.6 VSS 4 5 6 7 8 9 3 2 1 25 24 23 fo VPP 11 VREG 12 Pin Definitions Name D-/SDATA, D+/SCLK P0[7:0] I/O I/O I/O 18-Pin 12 13 24-Pin 15 16 en CY7C63723C CY7C63743C CY7C63722C 25-Pad 16 17 de Description USB differential data lines (D- and D+), or PS/2 clock and data signals (SDATA and SCLK) XTALIN/P2.1 XTALOUT VPP VCC VREG/P2.0 VSS ot R P1[7:0] I/O ec IN om 1, 2, 3, 4, 15, 16, 17, 18 5, 14 9 10 7 11 8 6 m 1, 2, 3, 4, 1, 2, 3, 4, GPIO Port 0 capable of sinking up to 50 mA/pin, or 21, 22, 23, 24 22, 23, 24, 25 sinking controlled low or high programmable current. Can also source 2 mA current, provide a resistive pull-up, or serve as a high-impedance input. P0.0 and P0.1 provide inputs to Capture Timers A and B, respectively. 5, 6, 7, 8, 5, 6, 7, 8, IO Port 1 capable of sinking up to 50 mA/pin, or sinking 17, 18, 19, 20 18, 19, 20, 21 controlled low or high programmable current. Can also source 2 mA current, provide a resistive pull-up, or serve as a high-impedance input. 12 13 10 14 11 9 13 14 11 15 12 9, 10 6-MHz ceramic resonator or external clock input, or P2.1 input 6-MHz ceramic resonator return pin or internal oscillator output Programming voltage supply, ground for normal operation Voltage supply for 1.3-k USB pull-up resistor (3.3V nominal). Also serves as P2.0 input. N OUT Document #: 38-08022 Rev. *D XTALIN/P2.1 XTALOUT VCC D-/SDATA d 13 14 15 16 D es CY7C63722C-XC DIE P0.2 P0.1 P0.0 P0.4 P0.5 P0.6 22 21 20 19 18 P0.7 P1.1 P1.3 P1.5 P1.7 VSS 10 17 D+/SCLK Top View ig Page 3 of 53 [+] Feedback Pin Configurations ns CY7C63722C CY7C63723C CY7C63743C Programming Model Refer to the CYASM Assembler User's Guide for more details on firmware operation with the CY7C637xxC microcontrollers. decremented again and the first byte is restored from memory addressed by the PSP. After the program counter and flags have been restored from stack, the interrupts are enabled. The effect is to restore the program counter and flags from the program stack, decrement the program stack pointer by two, and reenable interrupts. The call subroutine (CALL) instruction stores the program counter and flags on the program stack and increments the PSP by two. Program Counter (PC) The 14-bit program counter (PC) allows access for up to 8 Kbytes of EPROM using the CY7C637xxC architecture. The program counter is cleared during reset, such that the first instruction executed after a reset is at address 0x0000. This instruction is typically a jump instruction to a reset handler that initializes the application. The lower 8 bits of the program counter are incremented as instructions are loaded and executed. The upper six bits of the program counter are incremented by executing an XPAGE instruction. As a result, the last instruction executed within a 256-byte "page" of sequential code should be an XPAGE instruction. The assembler directive "XPAGEON" will cause the assembler to insert XPAGE instructions automatically. As instructions can be either one or two bytes long, the assembler may occasionally need to insert a NOP followed by an XPAGE for correct execution. The program counter of the next instruction to be executed, carry flag, and zero flag are saved as two bytes on the program stack during an interrupt acknowledge or a CALL instruction. The program counter, carry flag, and zero flag are restored from the program stack only during a RETI instruction. Please note the program counter cannot be accessed directly by the firmware. The program stack can be examined by reading SRAM from location 0x00 and up. 8-bit Data Stack Pointer (DSP) The data stack pointer (DSP) supports PUSH and POP instructions that use the data stack for temporary storage. A PUSH instruction will pre-decrement the DSP, then write data to the memory location addressed by the DSP. A POP instruction will read data from the memory location addressed by the DSP, then post-increment the DSP. During a reset, the Data Stack Pointer will be set to zero. A PUSH instruction when DSP equals zero will write data at the top of the data RAM (address 0xFF). This would write data to the memory area reserved for a FIFO for USB endpoint 0. In non-USB applications, this works fine and is not a problem. For USB applications, the firmware should set the DSP to an appropriate location to avoid a memory conflict with RAM dedicated to USB FIFOs. The memory requirements for the USB endpoints are shown in Section . For example, assembly instructions to set the DSP to 20h (giving 32 bytes for program and data stack combined) are shown below. MOV A,20h ; Move 20 hex into Accumulator (must be D8h or less to avoid USB FIFOs) SWAP A,DSP ; swap accumulator value into DSP register 8-bit Accumulator (A) The accumulator is the general-purpose, do everything register in the architecture where results are usually calculated. 8-bit Index Register (X) om The index register "X" is available to the firmware as an auxiliary accumulator. The X register also allows the processor to perform indexed operations by loading an index value into X. m en de ec 8-bit Program Stack Pointer (PSP) During an interrupt acknowledge, interrupts are disabled and the program counter, carry flag, and zero flag are written as two bytes of data memory. The first byte is stored in the memory addressed by the program stack pointer, then the PSP is incremented. The second byte is stored in memory addressed by the program stack pointer and the PSP is incremented again. The net effect is to store the program counter and flags on the program "stack" and increment the program stack pointer by two. The return from interrupt (RETI) instruction decrements the program stack pointer, then restores the second byte from memory addressed by the PSP. The program stack pointer is N During a reset, the program stack pointer (PSP) is set to zero. This means the program "stack" starts at RAM address 0x00 and "grows" upward from there. Note that the program stack pointer is directly addressable under firmware control, using the MOV PSP,A instruction. The PSP supports interrupt service under hardware control and CALL, RET, and RETI instructions under firmware control. ot R Document #: 38-08022 Rev. *D d fo Address Modes The CY7C637xxC microcontrollers support three addressing modes for instructions that require data operands: data, direct, and indexed. Data The "Data" address mode refers to a data operand that is actually a constant encoded in the instruction. As an example, consider the instruction that loads A with the constant 0x30: This instruction will require two bytes of code where the first byte identifies the "MOV A" instruction with a data operand as the second byte. The second byte of the instruction will be the constant "0xE8h". A constant may be referred to by name if a prior "EQU" statement assigns the constant value to the name. For example, the following code is equivalent to the example shown above. rN ew MOV A, 30h DSPINIT: EQU 30h D es Note that there are restrictions in using the JMP, CALL, and INDEX instructions across the 4-KByte boundary of the program memory. Refer to the CYASM Assembler User's Guide for a detailed description. ig The return from subroutine (RET) instruction restores the program counter, but not the flags, from program stack and decrements the PSP by two. ns Page 4 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C MOV A,DSPINIT Indexed "Indexed" address mode allows the firmware to manipulate arrays of data stored in SRAM. The address of the data operand is the sum of a constant encoded in the instruction and the contents of the "X" register. In normal usage, the constant will be the "base" address of an array of data and the X register will contain an index that indicates which element of the array is actually addressed. Direct "Direct" address mode is used when the data operand is a variable stored in SRAM. In that case, the one byte address of the variable is encoded in the instruction. As an example, consider an instruction that loads A with the contents of memory address location 0x10h: MOV A, [10h] array: EQU 10h MOV X,3 MOV A, [x+array] buttons: EQU 10h MOV A, [buttons] This would have the effect of loading A with the fourth element of the SRAM "array" that begins at address 0x10h. The fourth element would be at address 0x13h. Refer to the CYASM Assembler User's Guide for detailed information on these instructions. Note that conditional jump instructions (i.e., JC, JNC, JZ, JNZ) take five cycles if jump is taken, four cycles if no jump. MNEMONIC HALT ADD A,expr ADD A,[expr] ADD A,[X+expr] ADC A,expr ADC A,[expr] ADC A,[X+expr] SUB A,expr SUB A,[expr] SUB A,[X+expr] SBB A,expr SBB A,[expr] SBB A,[X+expr] OR A,expr OR A,[expr] data direct index data direct index data direct index data Operand Opcode 00 01 02 03 04 05 06 07 08 Cycles 7 4 6 7 4 rN ew MNEMONIC NOP INC A INC X acc x INC [expr] INC [X+expr] DEC A DEC X DEC [expr] DEC [X+expr] IORD expr IOWR expr POP A POP X PUSH A PUSH X SWAP A,X SWAP A,DSP MOV [expr],A MOV [X+expr],A OR [expr],A OR [X+expr],A AND [expr],A AND [X+expr],A XOR [expr],A XOR [X+expr],A IOWX [X+expr] acc x Instruction Set Summary D es Operand 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 direct index direct index direct index direct index index 31 32 33 34 35 36 37 38 39 direct index direct index address address In normal usage, variable names are assigned to variable addresses using "EQU" statements to improve the readability of the assembler source code. As an example, the following code is equivalent to the example shown above. ig Opcode 4 4 4 7 8 4 4 7 8 5 5 4 4 5 5 5 5 5 6 7 8 7 8 7 8 6 Page 5 of 53 Cycles [+] Feedback m om 09 0A ec direct 0B index 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 ot R data direct OR A,[X+expr] AND A,expr AND A,[expr] XOR A,expr XOR A,[expr] index data direct index data direct N AND A,[X+expr] XOR A,[X+expr] CMP A,expr CMP A,[expr] CMP A,[X+expr] MOV A,expr index data direct index data Document #: 38-08022 Rev. *D en 6 7 4 6 7 4 6 7 4 6 7 4 6 7 4 6 7 5 7 8 4 de d fo ns CY7C63722C CY7C63723C CY7C63743C MNEMONIC MOV A,[expr] MOV A,[X+expr] MOV X,expr MOV X,[expr] reserved XPAGE MOV A,X MOV X,A MOV PSP,A CALL JMP CALL JZ JNZ Operand direct index data direct Opcode 1A 1B 1C 1D 1E 1F 40 41 60 Cycles 5 6 4 5 4 4 4 4 10 5 10 5 (or 4) 5 (or 4) JC JNC CPL ASL ASR RLC RRC RET DI EI RETI MNEMONIC Operand Opcode 3A 3B 3C 3D 3E 3F 70 72 73 4 4 4 4 4 8 4 Cycles ig D es addr addr addr addr F0-FF C0-CF D0-DF E0-EF addr addr addr addr addr 50 - 5F 80-8F 90-9F A0-AF B0-BF INDEX rN ew JACC Document #: 38-08022 Rev. *D N ot R ec om m en de d fo ns 4 8 5 (or 4) 5 (or 4) 7 14 Page 6 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Memory Organization Program Memory Organization[1] After reset 14 -bit PC Address 0x0000 0x0002 0x0004 0x0006 0x0008 0x000A 0x000C 0x000E 0x0010 0x0012 0x0014 0x0016 0x0018 Program execution begins here after a reset USB Bus Reset interrupt vector 128-s timer interrupt vector 1.024-ms timer interrupt vector USB endpoint 0 interrupt vector USB endpoint 1 interrupt vector USB endpoint 2 interrupt vector SPI interrupt vector Capture timer B interrupt vector GPIO interrupt vector Wake-up interrupt vector Program Memory begins here N ot R ec om m Figure 1. Program Memory Space with Interrupt Vector Table Note 1. The upper 32 bytes of the 8K PROM are reserved. Therefore, the user's program must not overwrite this space. Document #: 38-08022 Rev. *D en 0x1FDF de 8 KB PROM ends here (8K - 32 bytes). See Note below d fo Capture timer A interrupt Vector rN ew D es Page 7 of 53 [+] Feedback ig ns CY7C63722C CY7C63723C CY7C63743C Data Memory Organization The CY7C637xxC microcontrollers provide 256 bytes of data RAM. In normal usage, the SRAM is partitioned into four areas: program stack, data stack, user variables and USB endpoint FIFOs as shown below. Figure 2. Data Memory Organization After reset 8-bit DSP 8-bit PSP (User's firmware moves DSP) Address 0x00 8-bit DSP User Selected User Variables Data Stack Growth 0xE8 USB FIFO for Address A endpoint 2 0xF0 Top of RAM Memory 0xFF Table 1. I/O Register Summary Register Name Port 0 Data Port 1 Data ot R ec I/O registers are accessed via the I/O Read (IORD) and I/O Write (IOWR, IOWX) instructions. IORD reads the selected port into the accumulator. IOWR writes data from the accumulator to the selected port. Indexed I/O Write (IOWX) adds the contents of X to the address in the instruction to form the port address and writes data from the accumulator to the specified port. Note that m I/O Register Summary en de om I/O Address 0x00 0x01 0x02 0x04 0x05 0x06 0x07 0x0A 0x0B 0x0C 0x0D Read/Write R/W R/W R W W W W W W W W GPIO Port 0 GPIO Port 1 d 0xF8 USB FIFO for Address A endpoint 0 fo USB FIFO for Address A endpoint 1 specifying address 0 with IOWX (e.g., IOWX 0h) means the I/O port is selected solely by the contents of X. Note: All bits of all registers are cleared to all zeros on reset, except the Processor Status and Control Register (Figure 33). All registers not listed are reserved, and should never be written by firmware. All bits marked as reserved should always be written as 0 and be treated as undefined by reads. rN ew Function D es Fig 7 8 37 38 39 9 11 12 Page 8 of 53 [+] Feedback Port 0 Interrupt Enable Port 1 Interrupt Enable Port 0 Interrupt Polarity Port 1 Interrupt Polarity Port 0 Mode0 Port 0 Mode1 Port 1 Mode0 Port 1 Mode1 N Port 2 Data Auxiliary input register for D+, D-, VREG, XTALIN Interrupt enable for pins in Port 0 Interrupt enable for pins in Port 1 Interrupt polarity for pins in Port 0 Interrupt polarity for pins in Port 1 Controls output configuration for Port 0 Controls output configuration for Port 1 Document #: 38-08022 Rev. *D ig ns Program Stack Growth CY7C63722C CY7C63723C CY7C63743C Table 1. I/O Register Summary (continued) Register Name USB Device Address EP0 Counter Register EP0 Mode Register EP1 Counter Register EP1 Mode Register EP2 Counter Register EP2 Mode Register USB Status & Control Global Interrupt Enable Endpoint Interrupt Enable Timer (LSB) Timer (MSB) WDR Clear Capture Timer A Rising Capture Timer A Falling Capture Timer B Rising Capture Timer B Falling Capture TImer Configuration Capture Timer Status SPI Data SPI Control Clock Configuration Processor Status & Control I/O Address 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x1F 0x20 0x21 0x24 0x25 0x26 0x40 0x41 0x42 0x43 0x44 0x45 0x60 0x61 0xF8 0xFF Read/Write R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R W R R R R R/W R R/W Function USB Device Address register USB Endpoint 0 counter register USB Endpoint 0 configuration register USB Endpoint 1 counter register USB Endpoint 1 configuration register USB Endpoint 2 counter register USB Endpoint 2 configuration register USB status and control register Global interrupt enable register Fig 15 18 16 18 ig USB endpoint interrupt enables Lower 8 bits of free-running timer (1 MHz) Watchdog Reset clear D es rN ew Upper 4 bits of free-running timer Rising edge Capture Timer A data register Falling edge Capture Timer A data register Rising edge Capture Timer B data register ns 18 14 24 25 - 29 30 32 31 21 22 33 en R/W Document #: 38-08022 Rev. *D N ot R ec om m de R/W R/W d fo Falling edge Capture Timer B data register Capture Timer configuration register Capture Timer status register SPI read and write data register SPI status and control register Internal / External Clock configuration register Processor status and control Page 9 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Clocking The chip can be clocked from either the internal on-chip clock, or from an oscillator based on an external resonator/crystal, as shown in Figure . No additional capacitance is included on chip at the XTALIN/OUT pins. Operation is controlled by the Clock Configuration Register, Figure . Figure 3. Clock Oscillator On-chip Circuit Int Clk Output Disable Internal Osc Ext Clk Enable Clk2x (12 MHz) (to Microcontroller) Clk1x (6 MHz) (to USB SIE) Port 2.1 rN ew de 5 Clock Doubler D es XTALIN Figure 4. Clock Configuration Register (Address 0xF8) 6 Bit # Bit Name 7 Ext. Clock Resume Delay R/W 0 en d fo 4 3 Low-voltage Reset Disable R/W 0 2 Precision USB Clocking Enable R/W 0 ig 1 Internal Clock Output Disable R/W 0 R/W 0 R/W 0 Bit [6:4]: Wake-up Timer Adjust Bit [2:0] m Wake-up Timer Adjust Bit [2:0] Read/Write Reset om R/W 0 ec ot R Bit 7: Ext. Clock Resume Delay External Clock Resume Delay bit selects the delay time when switching to the external oscillator from the internal oscillator mode, or when waking from suspend mode with the external oscillator enabled. 1 = 4 ms delay. 0 = 128 s delay. The delay gives the oscillator time to start up. The shorter time is adequate for operation with ceramic resonators, while the longer time is preferred for start-up with a crystal. (These times do not include an initial oscillator start-up time which depends on the resonating element. This time is typically 50-100 s for ceramic resonators and 1-10 ms for crystals). Note that this bit only selects the delay time for the external clock mode. When waking from suspend mode with the internal oscillator (Bit 0 is LOW), the delay time is only 8 s in addition to a delay of approximately 1 s for the oscillator to start. The Wake-up Timer Adjust Bits are used to adjust the Wake-up timer period. If the Wake-up interrupt is enabled in the Global Interrupt Enable Register, the microcontroller will generate wake-up interrupts periodically. The frequency of these periodical wake-up interrupts is adjusted by setting the Wake-up Timer Adjust Bit [2:0], as described in Section . One common use of the wake-up interrupts is to generate periodical wake-up events during suspend mode to check for changes, such as looking for movement in a mouse, while maintaining a low average power. Document #: 38-08022 Rev. *D N ns XTALOUT 0 External Oscillator Enable R/W 0 Page 10 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Bit 3: Low-voltage Reset Disable When VCC drops below VLVR (see Section for the value of VLVR) and the Low-voltage Reset circuit is enabled, the microcontroller enters a partial suspend state for a period of tSTART (see Section for the value of tSTART). Program execution begins from address 0x0000 after this tSTART delay period. This provides time for VCC to stabilize before the part executes code. See Section for more details. 1 = Disables the LVR circuit. 0 = Enables the LVR circuit. Bit 2: Precision USB Clocking Enable The Precision USB Clocking Enable only affects operation in internal oscillator mode. In that mode, this bit must be set to 1 to cause the internal clock to automatically precisely tune to USB timing requirements (6 MHz 1.5%). The frequency may have a looser initial tolerance at power-up, but all USB transmissions from the chip will meet the USB specification. 1 = Enabled. The internal clock accuracy is 6 MHz 1.5% after USB traffic is received. 0 = Disabled. The internal clock accuracy is 6 MHz 5%. Bit 1: Internal Clock Output Disable The Internal Clock Output Disable is used to keep the internal clock from driving out to the XTALOUT pin. This bit has no effect in the external oscillator mode. steps involved in switching from Internal to External Clock mode are as follows: 1. At reset, chip begins operation using the internal clock. 2. Firmware sets Bit 0 of the Clock Configuration Register. For example, ; Set Bit 0 HIGH (External Oscillator Enable bit). Bit 7 cleared gives faster start-up iowr F8h ; Write to Clock Configuration Register 3. Internal clocking is halted, the internal oscillator is disabled, and the external clock oscillator is enabled. 4. After the external clock becomes stable, chip clocks are re-enabled using the external clock signal. (Note that the time for the external clock to become stable depends on the external resonating device; see next section.) 5. After an additional delay the CPU is released to run. This delay depends on the state of the Ext. Clock Resume Delay bit of the Clock Configuration Register. The time is 128 s if the bit is 0, or 4 ms if the bit is 1. 6. Once the chip has been set to external oscillator, it can only return to internal clock when waking from suspend mode. Clearing bit 0 of the Clock Configuration Register will not re-enable internal clock mode until suspend mode is entered. See Section for more details on suspend mode operation. mov A, 1h en 0 = Enable the internal clock output. The internal clock is driven out to the XTALOUT pin. Bit 0: External Oscillator Enable de 1 = Disable internal clock output. XTALOUT pin will drive HIGH. 1 = Enable the external oscillator. The clock is switched to external clock mode, as described in Section . 0 = Enable the internal oscillator. ot R At power-up, the chip operates from the internal clock by default. Setting the External Oscillator Enable bit HIGH disables the internal clock, and halts the part while the external resonator/crystal oscillator is started. Clearing this bit has no immediate effect, although the state of this bit is used when waking out of suspend mode to select between internal and external clock. In internal clock mode, XTALIN pin will be configured as an input with a weak pull-down and can be used as a GPIO input (P2.1). ec om m The internal oscillator provides an operating clock, factory set to a nominal frequency of 6 MHz. This clock requires no external components. At power-up, the chip operates from the internal clock. In this mode, the internal clock is buffered and driven to the XTALOUT pin by default, and the state of the XTALIN pin can be read at Port 2.1. While the internal clock is enabled, its output can be disabled at the XTALOUT pin by setting the Internal Clock Output Disable bit of the Clock Configuration Register. Setting the External Oscillator Enable bit of the Clock Configuration Register HIGH disables the internal clock, and halts the part while the external resonator/crystal oscillator is started. The Document #: 38-08022 Rev. *D N Internal/External Oscillator Operation d fo If the Internal Clock is enabled, the XTALIN pin can serve as a general purpose input, and its state can be read at Port 2, Bit 1 (P2.1). Refer to Figure for the Port 2 Data Register. In this mode, there is a weak pull-down at the XTALIN pin. This input cannot provide an interrupt source to the CPU. External Oscillator The user can connect a low-cost ceramic resonator or an external oscillator to the XTALIN/XTALOUT pins to provide a precise reference frequency for the chip clock, as shown in Figure . The external components required are a ceramic resonator or crystal and any associated capacitors. To run from the external resonator, the External Oscillator Enable bit of the Clock Configuration Register must be set to 1, as explained in the previous section. Start-up times for the external oscillator depend on the resonating device. Ceramic resonator based oscillators typically start in less than 100 s, while crystal based oscillators take longer, typically 1 to 10 ms. Board capacitance should be minimized on the XTALIN and XTALOUT pins by keeping the traces as short as possible. An external 6-MHz clock can be applied to the XTALIN pin if the XTALOUT pin is left open. Reset The USB Controller supports three types of resets. The effects of the reset are listed below. The reset types are: 1. Low-voltage Reset (LVR) 2. Brown Out Reset (BOR) 3. Watchdog Reset (WDR) The occurrence of a reset is recorded in the Processor Status and Control Register (Figure 33). Bits 4 (Low-voltage or Page 11 of 53 rN ew D es ig ns [+] Feedback CY7C63722C CY7C63723C CY7C63743C Brown-out Reset bit) and 6 (Watchdog Reset bit) are used to record the occurrence of LVR/BOR and WDR respectively. The firmware can interrogate these bits to determine the cause of a reset. The microcontroller begins execution from ROM address 0x0000 after a LVR, BOR, or WDR reset. Although this looks like interrupt vector 0, there is an important difference. Reset processing does NOT push the program counter, carry flag, and zero flag onto program stack. Attempting to execute either a RET or RETI in the reset handler will cause unpredictable execution results. The following events take place on reset. More details on the various resets are given in the following sections. 1. All registers are reset to their default states (all bits cleared, except in Processor Status and Control Register). 2. GPIO and USB pins are set to high-impedance state. 3. The VREG pin is set to high-impedance state. 4. Interrupts are disabled. 5. USB operation is disabled and must be enabled by firmware if desired, as explained in Section . 6. For a BOR or LVR, the external oscillator is disabled and Internal Clock mode is activated, followed by a time-out period tSTART for VCC to stabilize. A WDR does not change the clock mode, and there is no delay for VCC stabilization on a WDR. Note that the External Oscillator Enable (Bit 0, Figure ) will be cleared by a WDR, but it does not take effect until suspend mode is entered. 7. The Program Stack Pointer (PSP) and Data Stack Pointer (DSP) reset to address 0x00. Firmware should move the DSP for USB applications, as explained in Section . 8. Program execution begins at address 0x0000 after the appropriate time-out period. As long as the LVR circuit is enabled, this reset sequence repeats whenever the VCC pin voltage drops below VLVR. The LVR can be disabled by firmware by setting the Low-voltage Reset Disable bit in the Clock Configuration Register (Figure ). In addition, the LVR is automatically disabled in suspend mode to save power. If the LVR was enabled before entering suspend mode, it becomes active again once the suspend mode ends. When LVR is disabled during normal operation (i.e., by writing `0' to the Low-voltage Reset Disable bit in the Clock Configuration Register), the chip may enter an unknown state if VCC drops below VLVR. Therefore, LVR should be enabled at all times during normal operation. If LVR is disabled (i.e., by firmware or during suspend mode), a secondary low-voltage monitor, BOR, becomes active, as described in the next section. The LVR/BOR Reset bit of the Processor Status and Control Register (Figure 33), is set to `1' if either a LVR or BOR has occurred. Brown Out Reset (BOR) de en Low-voltage Reset (LVR) ec When VCC is first applied to the chip, the internal oscillator is started and the Low-voltage Reset is initially enabled by default. At the point where VCC has risen above VLVR (see Section for the value of VLVR), an internal counter starts counting for a period of tSTART (see Section for the value of tSTART). During this tSTART time, the microcontroller enters a partial suspend state to wait for VCC to stabilize before it begins executing code from address 0x0000. ot R N WDR om tWATCH = 10.1 to 14.6 ms (at FOSC = 6 MHz) m Figure 5. Watchdog Reset (WDR, Address 0x26) At least 10.1 ms since last write to WDR d 2-4 ms WDR goes HIGH for 2-4 ms fo The Brown Out Reset (BOR) circuit is always active and behaves like the POR. BOR is asserted whenever the VCC voltage to the device is below an internally defined trip voltage of approximately 2.5V. The BOR re-enables LVR. That is, once VCC drops and trips BOR, the part remains in reset until VCC rises above VLVR. At that point, the tSTART delay occurs before normal operation resumes, and the microcontroller starts executing code from address 0x00 after the tSTART delay. In suspend mode, only the BOR detection is active, giving a reset if VCC drops below approximately 2.5V. Since the device is suspended and code is not executing, this lower reset voltage is safe for retaining the state of all registers and memory. Note that in suspend mode, LVR is disabled as discussed in Section . Watchdog Reset (WDR) The Watchdog Timer Reset (WDR) occurs when the internal Watchdog timer rolls over. Writing any value to the write-only Watchdog Reset Register at address 0x26 will clear the timer. The timer will roll over and WDR will occur if it is not cleared within tWATCH (see Figure 10) of the last clear. Bit 6 (Watchdog Reset bit) of the Processor Status and Control Register is set to record this event (see Section for more details). A Watchdog Timer Reset typically lasts for 2-4 ms, after which the microcontroller begins execution at ROM address 0x0000. Document #: 38-08022 Rev. *D rN ew Execution begins at ROM Address 0x0000 D es ig ns Page 12 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Suspend Mode The CY7C637xxC parts support a versatile low-power suspend mode. In suspend mode, only an enabled interrupt or a LOW state on the D-/SDATA pin will wake the part. Two options are available. For lowest power, all internal circuits can be disabled, so only an external event will resume operation. Alternatively, a low-power internal wake-up timer can be used to trigger the wake-up interrupt. This timer is described in Section , and can be used to periodically poll the system to check for changes, such as looking for movement in a mouse, while maintaining a low average power. The CY7C637xxC is placed into a low-power state by setting the Suspend bit of the Processor Status and Control Register (Figure 33). All logic blocks in the device are turned off except the GPIO interrupt logic, the D-/SDATA pin input receiver, and (optionally) the wake-up timer. The clock oscillators, as well as the free-running and Watchdog timers are shut down. Only the occurrence of an enabled GPIO interrupt, wake-up interrupt, SPI slave interrupt, or a LOW state on the D-/SDATA pin will wake the part from suspend (D- LOW indicates non-idle USB activity). Once one of these resuming conditions occurs, clocks will be restarted and the device returns to full operation after the oscillator is stable and the selected delay period expires. This delay period is determined by selection of internal vs. external clock, and by the state of the Ext. Clock Resume Delay as explained in Section . In suspend mode, any enabled and pending interrupt will wake the part up. The state of the Interrupt Enable Sense bit (Bit 2, Figure 33) does not have any effect. As a result, any interrupts not intended for waking from suspend should be disabled through the Global Interrupt Enable Register and the USB End Point Interrupt Enable Register (Section ). If a resuming condition exists when the suspend bit is set, the part will still go into suspend and then awake after the appropriate delay time. The Run bit in the Processor Status and Control Register must be set for the part to resume out of suspend. Once the clock is stable and the delay time has expired, the microcontroller will execute the instruction following the I/O write that placed the device into suspend mode before servicing any interrupt requests. To achieve the lowest possible current during suspend mode, all I/O should be held at either VCC or ground. In addition, the GPIO bit interrupts (Figure 37 and Figure 38) should be disabled for any pins that are not being used for a wake-up interrupt. This should be done even if the main GPIO Interrupt Enable (Figure ) is off. Typical code for entering suspend is shown below: ... ; All GPIO set to low-power state (no floating pins, and bit interrupts disabled unless using for wake-up) ... ; Enable GPIO and/or wake-up timer interrupts if desired for wake-up ... ; Select clock mode for wake-up (see Section ) mov a, 09h ; Set suspend and run bits iowr FFh ; Write to Status and Control Register - Enter suspend, wait for GPIO/wake-up interrupt or USB activity nop ; This executes before any ISR ... ; Remaining code for exiting suspend routine Clocking Mode on Wake-up from Suspend When exiting suspend on a wake-up event, the device can be configured to run in either Internal or External Clock mode. The mode is selected by the state of the External Oscillator Enable bit in the Clock Configuration Register (Figure ). Using the Internal Clock saves the external oscillator start-up time and keeps that oscillator off for additional power savings. The external oscillator mode can be activated when desired, similar to operation at power-up. The sequence of events for these modes is as follows: Wake in Internal Clock Mode: 1. Before entering suspend, clear bit 0 of the Clock Configuration Register. This selects Internal clock mode after suspend. 2. Enter suspend mode by setting the suspend bit of the Processor Status and Control Register. 3. After a wake-up event, the internal clock starts immediately (within 2 s). 4. A time-out period of 8 s passes, and then firmware execution begins. 5. At some later point, to activate External Clock mode, set bit 0 of the Clock Configuration Register. This halts the internal clocks while the external clock becomes stable. After an additional time-out (128 s or 4 ms, see Section ), firmware execution resumes. Wake in External Clock Mode: 1. Before entering suspend, the external clock must be selected by setting bit 0 of the Clock Configuration Register. Make sure this bit is still set when suspend mode is entered. This selects External clock mode after suspend. 2. Enter suspend mode by setting the suspend bit of the Processor Status and Control Register. 3. After a wake-up event, the external oscillator is started. The clock is monitored for stability (this takes approximately 50-100 s with a ceramic resonator). 4. After an additional time-out period (128 s or 4 ms, see Section ), firmware execution resumes. om m en de ec Document #: 38-08022 Rev. *D N ot R d fo Wake-up Timer The wake-up timer runs whenever the wake-up interrupt is enabled, and is turned off whenever that interrupt is disabled. Operation is independent of whether the device is in suspend mode or if the global interrupt bit is enabled. Only the Wake-up Timer Interrupt Enable bit (Figure ) controls the wake-up timer. Once this timer is activated, it will give interrupts after its time-out period (see below). These interrupts continue periodically until the interrupt is disabled. Whenever the interrupt is disabled, the wake-up timer is reset, so that a subsequent enable always results in a full wake-up time. The wake-up timer can be adjusted by the user through the Wake-up Timer Adjust bits in the Clock Configuration Register (Figure ). These bits clear on reset. In addition to allowing the user to select a range for the wake-up time, a firmware algorithm can be used to tune out initial process and operating condition variations in this wake-up time. This can be done by timing the wake-up interrupt time with the accurate 1.024-ms timer interrupt, and adjusting the Timer Adjust bits accordingly to approximate the desired wake-up time. Page 13 of 53 rN ew D es ig ns [+] Feedback CY7C63722C CY7C63723C CY7C63743C Table 2. Wake-up Timer Adjust Settings Adjust Bits [2:0] (Bits [6:4] in Figure ) 000 (reset state) 001 010 011 100 101 110 111 Wakeup Time 1 * tWAKE 2 * tWAKE 4 * tWAKE 16 * tWAKE 32 * tWAKE 64 * tWAKE 128 * tWAKE See Switching Characteristics on page 43 for the value of tWAKE Ports 0 and 1 provide up to 16 versatile GPIO pins that can be read or written (the number of pins depends on package type). Figure shows a diagram of a GPIO port pin. Figure 6. Block Diagram of GPIO Port (one pin shown) (=1 if SPI inactive, or for non-SPI pins) Internal Data Bus en Data Out Register de Control d SPI Bypass (P0.5-P0.7 only) fo GPIO Mode 2 rN ew VCC Q1 Q3 14 k Q2 To Interrupt Controller General Purpose I/O Ports Port Write om m (Data Reg must be 1 for SPI outputs) Threshold Select ec ot R Port Read To Capture Timers (P0.0, P0.1) and SPI (P0.4-P0.7)) Interrupt Polarity Interrupt Enable Interrupt Logic N Port 0 is an 8-bit port; Port 1 contains either 2 bits, P1.1-P1.0 in the CY7C63723C, or all 8 bits, P1.7-P1.0 in the CY7C63743C parts. Each bit can also be selected as an interrupt source for the microcontroller, as explained in Section . The data for each GPIO pin is accessible through the Port Data register. Writes to the Port Data register store outgoing data state for the port pins, while reads from the Port Data register return the actual logic value on the port pins, not the Port Data register contents. Document #: 38-08022 Rev. *D Each GPIO pin is configured independently. The driving state of each GPIO pin is determined by the value written to the pin's Data Register and by two associated pin's Mode0 and Mode1 bits. The Port 0 Data Register is shown in Figure 7, and the Port 1 Data Register is shown in Figure 8. The Mode0 and Mode1 bits for the two GPIO ports are given in Figure 9 through Figure 12. D es GPIO Pin Page 14 of 53 [+] Feedback ig ns 8 * tWAKE CY7C63722C CY7C63723C CY7C63743C Figure 7. Port 0 Data (Address 0x00) Bit # Bit Name Reset 0 0 0 0 7 6 5 4 P0 0 0 0 0 3 2 1 0 Bit [7:0]: P0[7:0] Mode 1 1 = Port Pin Mode 1 is logic HIGH 0 = Port Pin Mode 1 is logic LOW Figure 11. GPIO Port 1 Mode0 Register (Address 0x0C) Bit # Bit Name Read/Write Bit [7:0]: P0[7:0] 1 = Port Pin is logic HIGH 0 = Port Pin is logic LOW Figure 8. Port 1 Data (Address 0x01) Bit # Bit Name Notes 7 6 5 4 P1 Pins 7:2 only in CY7C63743C Pins 1:0 in all parts 0 0 3 2 1 0 Reset W 0 W 0 W 0 7 6 5 4 W 0 3 W 0 2 W 0 1 W 0 0 W 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W P1[7:0] Mode0 Bit [7:0]: P1[7:0] Mode 0 1 = Port Pin Mode 0 is logic HIGH Figure 12. GPIO Port 1 Mode1 Register (Address 0x0D) Bit # 7 6 5 W 0 4 W 0 3 W 0 2 W 0 1 W 0 0 W 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 rN ew Bit Name Reset Read/Write W 0 W 0 0 = Port Pin Mode 0 is logic LOW Bit [7:0]: P1[7:0] 1 = Port Pin is logic HIGH 0 = Port Pin is logic LOW de en d Figure 9. GPIO Port 0 Mode0 Register (Address 0x0A) m Bit Name Read/Write Reset W 0 W 0 om Bit # 7 6 5 4 3 2 1 W 0 0 W 0 P0[7:0] Mode0 W 0 W 0 W 0 W 0 ot R ec Bit [7:0]: P0[7:0] Mode 0 1 = Port 0 Mode 0 is logic HIGH Figure 10. GPIO Port 0 Mode1 Register (Address 0x0B) Bit # Bit Name Read/Write Reset W 0 W 0 W 0 7 6 5 4 W 0 3 W 0 2 W 0 1 W 0 0 W 0 N 0 = Port 0 Mode 0 is logic LOW P0[7:0] Mode1 Document #: 38-08022 Rev. *D fo Bit [7:0]: P1[7:0] Mode 1 1 = Port Pin Mode 1 is logic HIGH 0 = Port Pin Mode 1 is logic LOW Each pin can be independently configured as high-impedance inputs, inputs with internal pull-ups, open drain outputs, or traditional CMOS outputs with selectable drive strengths. The driving state of each GPIO pin is determined by the value written to the pin's Data Register and by its associated Mode0 and Mode1 bits. Table 3 lists the configuration states based on these bits. The GPIO ports default on reset to all Data and Mode Registers cleared, so the pins are all in a high-impedance state. The available GPIO output drive strength are: Hi-Z Mode (Mode1 = 0 and Mode0 = 0) Q1, Q2, and Q3 (Figure ) are OFF. The GPIO pin is not driven internally. Performing a read from the Port Data Register return the actual logic value on the port pins. Low Sink Mode (Mode1 = 1, Mode0 = 0, and the pin's Data Register = 0) Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of sinking 2 mA of current. Medium Sink Mode (Mode1 = 0, Mode0 = 1, and the pin's Data Register = 0) Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of sinking 8 mA of current. D es P1[7:0] Mode1 Page 15 of 53 [+] Feedback ig ns CY7C63722C CY7C63723C CY7C63743C High Sink Mode (Mode1 = 1, Mode0 = 1, and the pin's Data Register = 0) Q1 and Q3 are OFF. Q2 is ON. The GPIO pin is capable of sinking 50 mA of current. Bit [7:6]: Reserved Bit [5:4]: D+ (SCLK) and D- (SDATA) States The state of the D+ and D- pins can be read at Port 2 Data Register. Performing a read from the port pins returns their logic values. 1 = Port Pin is logic HIGH Bit [3:2]: Reserved 0 = Port Pin is logic LOW High Drive Mode (Mode1 = 0 or 1, Mode0 = 1, and the pin's Data Register = 1) Q1 and Q2 are OFF. Q3 is ON. The GPIO pin is capable of sourcing 2 mA of current. Note that open drain mode can be achieved by fixing the Data and Mode1 Registers LOW, and switching the Mode0 register. Input thresholds are CMOS, or TTL as shown in the table (See Section for the input threshold voltage in TTL or CMOS modes). Both input modes include hysteresis to minimize noise sensitivity. In suspend mode, if a pin is used for a wake-up interrupt using an external R-C circuit, CMOS mode is preferred for lowest power. Table 3. Ports 0 and 1 Output Control Truth Table Data Register 0 1 0 1 0 1 0 1 1 1 1 0 Input Mode1 Mode0 Output Drive Threshold Strength 0 0 0 1 Hi-Z Hi-Z Medium (8 mA) Sink High Drive Low (2 mA) Sink Resistive CMOS TTL CMOS 1 = Port Pin is logic HIGH 0 = Port Pin is logic LOW Bit 0: P2.0/VREG Pin State de en CMOS CMOS CMOS CMOS om High (50 mA) Sink High Drive m CMOS ec Auxiliary Input Port ot R Port 2 serves as an auxiliary input port as shown in Figure . The Port 2 inputs all have TTL input thresholds. Figure 13. Port 2 Data Register (Address 0x02) Bit # 7 6 5 4 3 2 1 0 P2.0 Reserved P2.1 D- Bit Reserved D+ (Internal VREG Name (SCLK) (SDATA) Pin Clock State State Mode State Only) Read/ Write Reset 0 0 R 0 R 0 0 0 R 0 R 0 N Document #: 38-08022 Rev. *D d fo USB Serial Interface Engine (SIE) The SIE allows the microcontroller to communicate with the USB host. The SIE simplifies the interface between the microcontroller and USB by incorporating hardware that handles the following USB bus activity independently of the microcontroller: Firmware is required to handle the rest of the USB interface with the following tasks: rN ew Bit stuffing/unstuffing. In PS/2 mode, the VREG pin can be used as an input and its state can be read at port P2.0. Section for more details. 1 = Port Pin is logic HIGH 0 = Port Pin is logic LOW Translate the encoded received data and format the data to be transmitted on the bus. CRC checking and generation. Flag the microcontroller if errors exist during transmission. Address checking. Ignore the transactions not addressed to the device. Send appropriate ACK/NAK/STALL handshakes. Token type identification (SETUP, IN, or OUT). Set the appropriate token bit once a valid token is received. Place valid received data in the appropriate endpoint FIFOs. Send and update the data toggle bit (Data1/0). Coordinate enumeration by decoding USB device requests. Fill and empty the FIFOs. Suspend/Resume coordination. Verify and select Data toggle values. D es Q2 and Q3 are OFF. Q1 is ON. The GPIO pin is pulled up with an internal 14-k resistor. Bit 1: P2.1 (Internal Clock Mode Only) In the Internal Clock mode, the XTALIN pin can serve as a general purpose input, and its state can be read at Port 2, Bit 1 (P2.1). See Section for more details. ig Resistive Mode (Mode1 = 1, Mode0 = 0, and the pin's Data Register = 1) ns Page 16 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C USB Enumeration A typical USB enumeration sequence is shown below. In this description, `Firmware' refers to embedded firmware in the CY7C637xxC controller. 1. The host computer sends a SETUP packet followed by a DATA packet to USB address 0 requesting the Device descriptor. 2. Firmware decodes the request and retrieves its Device descriptor from the program memory tables. 3. The host computer performs a control read sequence and Firmware responds by sending the Device descriptor over the USB bus, via the on-chip FIFO. 4. After receiving the descriptor, the host sends a SETUP packet followed by a DATA packet to address 0 assigning a new USB address to the device. 5. Firmware stores the new address in its USB Device Address Register after the no-data control sequence completes. 6. The host sends a request for the Device descriptor using the new USB address. 7. Firmware decodes the request and retrieves the Device descriptor from program memory tables. 8. The host performs a control read sequence and Firmware responds by sending its Device descriptor over the USB bus. 9. The host generates control reads from the device to request the Configuration and Report descriptors. 10.Once the device receives a Set Configuration request, its functions may now be used. 11.Firmware should take appropriate action for Endpoint 1 and/or 2 transactions, which may occur from this point. to approximately 1 Volt above VREG if the VREG Enable bit is set, or if the Device Address is enabled (bit 7 of the USB Device Address Register, Figure 15). 1 = Enable PS/2 Pull-up resistors. The SDATA and SCLK pins are pulled up internally to VCC with two resistors of approximately 5 k (see Section for the value of RPS2). 0 = Disable PS/2 Pull-up resistors. A 3.3V voltage regulator is integrated on chip to provide a voltage source for a 1.5-k pull-up resistor connected to the D- pin as required by the USB Specification. Note that the VREG output has an internal series resistance of approximately 200, the external pull-up resistor required is approximately 1.3-k (see Figure 19). 1 = Enable the 3.3V output voltage on the VREG pin. 0 = Disable. The VREG pin can be configured as an input. Bit 5: USB-PS/2 Interrupt Select This bit allows the user to select whether an USB bus reset interrupt or a PS/2 activity interrupt will be generated when the interrupt conditions are detected. 1 = PS/2 interrupt mode. A PS/2 activity interrupt will occur if the SDATA pin is continuously LOW for 128 to 256 s. d de en USB Port Status and Control Figure 14. USB Status and Control Register (Address 0x1F) Bit # 7 6 5 om 4 m USB status and control is regulated by the USB Status and Control Register as shown in Figure 14. 3 2:0 ot R Bit PS/2 VREG USB Reserved USB D+/D- Name Pull-up Enable ResetBus Forcing Enable PS/2 Activity Bit Activity Interrupt Mode ec Read/ R/W Write Reset 0 R/W 0 R/W 0 0 R/W 0 R/W 000 N Bit 7: PS/2 Pull-up Enable This bit is used to enable the internal PS/2 pull-up resistors on the SDATA and SCLK pins. Normally the output high level on these pins is VCC, but note that the output will be clamped Document #: 38-08022 Rev. *D fo Bit 4: Reserved. Must be written as a `0'. Bit 3: USB Bus Activity The Bus Activity bit is a "sticky" bit that detects any non-idle USB event has occurred on the USB bus. Once set to HIGH by the SIE to indicate the bus activity, this bit retains its logical HIGH value until firmware clears it. Writing a `0' to this bit clears it; writing a `1' preserves its value. The user firmware should check and clear this bit periodically to detect any loss of bus activity. Firmware can clear the Bus Activity bit, but only the SIE can set it. The 1.024-ms timer interrupt service routine is normally used to check and clear the Bus Activity bit. 1 = There has been bus activity since the last time this bit was cleared. This bit is set by the SIE. 0 = No bus activity since last time this bit was cleared (by firmware). Bit [2:0]: D+/D- Forcing Bit [2:0] Forcing bits allow firmware to directly drive the D+ and D- pins, as shown in Table 4. Outputs are driven with controlled edge rates in these modes for low EMI. For forcing the D+ and D- pins in USB mode, D+/D- Forcing Bit 2 should be 0. Setting D+/D- Forcing Bit 2 to `1' puts both pins in an open-drain mode, preferred for applications such as PS/2 or LED driving. rN ew 0 = USB interrupt mode (default state). In this mode, a USB bus reset interrupt will occur if the single ended zero (SE0, D- and D+ are LOW) exists for 128 to 256 s. See Section for more details. D es ig ns Bit 6: VREG Enable Page 17 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C USB Control Endpoint All USB devices are required to have an endpoint number 0 (EP0) that is used to initialize and control the USB device. EP0 provides access to the device configuration information and allows generic USB status and control accesses. EP0 is bidirectional as the device can both receive and transmit data. EP0 uses an 8-byte FIFO at SRAM locations 0xF8-0xFF, as shown in Section . The EP0 endpoint mode register uses the format shown in Figure 16. Bit # PS/2 Mode[2] 7 6 Table 4. Control Modes to Force D+/D- Outputs D+/D- Forcing Bit [2:0] 000 001 010 011 100 101 110 111 Control Action Application Any Mode USB Mode Not forcing (SIE controls driver) Force K (D+ HIGH, D- LOW) Force J (D+ LOW, D- HIGH) Force SE0 (D- LOW, D+ LOW) Force D- LOW, D+ LOW Force D- LOW, D+ HiZ Force D- HiZ, D+ LOW Force D- HiZ, D+ HiZ ig 5 4 R/W 0 R/W 0 ns 3:0 Bit SETUP IN OUT ACKed Mode Bit Name Received Received Received Transaction Read/ Write Reset R/W 0 R/W 0 R/W 0000 USB Device The CY7C637xxC supports one USB Device Address with three endpoints: EP0, EP1, and EP2. Figure 16. Endpoint 0 Mode Register (Address 0x12) The SIE provides a locking feature to prevent firmware from overwriting bits in the USB Endpoint 0 Mode Register. Writes to the register have no effect from the point that Bit[6:0] of the register are updated (by the SIE) until the firmware reads this register. The CPU can unlock this register by reading it. Because of these hardware-locking features, firmware should perform an read after a write to the USB Endpoint 0 Mode Register and USB Endpoint 0 Count Register (Figure 18) to verify that the contents have changed as desired, and that the SIE has not updated these values. Bit [7:4] of this register are cleared by any non-locked write to this register, regardless of the value written. Bit 7: SETUP Received 1 = A valid SETUP packet has been received. This bit is forced HIGH from the start of the data packet phase of the SETUP transaction until the start of the ACK packet returned by the SIE. The CPU is prevented from clearing this bit during this interval. While this bit is set to `1', the CPU cannot write to the EP0 FIFO. This prevents firmware from overwriting an incoming SETUP transaction before firmware has a chance to read the SETUP data. 0 = No SETUP received. This bit is cleared by any non-locked writes to the register. Bit 6: IN Received 1 = A valid IN packet has been received. This bit is updated to `1' after the last received packet in an IN transaction. This bit is cleared by any non-locked writes to the register. 0 = No IN received. This bit is cleared by any non-locked writes to the register. USB Address Register The USB Device Address Register contains a 7-bit USB address and one bit to enable USB communication. This register is cleared during a reset, setting the USB device address to zero and marking this address as disabled. Figure 15 shows the format of the USB Address Register. Bit # Bit Name 7 Device Address Enable R/W 0 0 0 6 5 4 3 2 1 0 Device Address Read/Write Reset R/W R/W R/W R/W R/W R/W R/W om 0 m 0 Figure 15. USB Device Address Register (Address 0x10) In either USB or PS/2 mode, this register is cleared by both hardware resets and the USB bus reset. See Section for more information on the USB Bus Reset - PS/2 interrupt. Bit 7: Device Address Enable This bit must be enabled by firmware before the serial interface engine (SIE) will respond to USB traffic at the address specified in Bit [6:0]. 1 = Enable USB device address. 0 = Disable USB device address. Bit [6:0]: Device Address Bit [6:0] These bits must be set by firmware during the USB enumeration process (i.e., SetAddress) to the non-zero address assigned by the USB host. Note 2. For PS/2 operation, the D+/D- Forcing Bit [2:0] = 111b mode must be set initially (one time only) before using the other PS/2 force modes Document #: 38-08022 Rev. *D N ot R ec en 0 de 0 0 d fo rN ew D es Page 18 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Bit 5: OUT Received 1 = A valid OUT packet has been received. This bit is updated to `1' after the last received packet in an OUT transaction. This bit is cleared by any non-locked writes to the register. 0 = No OUT received. This bit is cleared by any non-locked writes to the register. Bit 4: ACKed Transaction The ACKed Transaction bit is set whenever the SIE engages in a transaction to the register's endpoint that completes with an ACK packet. 1 = The transaction completes with an ACK. 0 = The transaction does not complete with an ACK. Bit [3:0]: Mode Bit[3:0] The endpoint modes determine how the SIE responds to USB traffic that the host sends to the endpoint. For example, if the endpoint Mode Bits [3:0] are set to 0001 which is NAK IN/OUT mode as shown in Table 8, the SIE will send NAK handshakes in response to any IN or OUT token sent to this endpoint. In this NAK IN/OUT mode, the SIE will send an ACK handshake when the host sends a SETUP token to this endpoint. The mode encoding is shown in Table 8. Additional information on the mode bits can be found in Table 9 and Table 10. These modes give the firmware total control on how to respond to different tokens sent to the endpoints from the host. In addition, the Mode Bits are automatically changed by the SIE in response to many USB transactions. For example, if the Mode Bit [3:0] are set to 1011 which is ACK OUT-NAK IN mode as shown in Table 8, the SIE will change the endpoint Mode Bit [3:0] to NAK IN/OUT (0001) mode after issuing an ACK handshake in response to an OUT token. Firmware needs to update the mode for the SIE to respond appropriately. Bit 7: STALL 1 = The SIE will stall an OUT packet if the Mode Bits are set to ACK-OUT, and the SIE will stall an IN packet if the mode bits are set to ACK-IN. See Section for the available modes. 0 = This bit must be set to LOW for all other modes. Bit [6:5]: Reserved. Must be written to zero during register writes. The ACKed transaction bit is set whenever the SIE engages in a transaction to the register's endpoint that completes with an ACK packet. 0 = The transaction does not complete with an ACK. Bit [3:0]: Mode Bit [3:0] The EP1 and EP2 Mode Bits operate in the same manner as the EP0 Mode Bits (see Section ). USB Endpoint Counter Registers There are three Endpoint Counter registers, with identical formats for both control and non-control endpoints. These registers contain byte count information for USB transactions, as well as bits for data packet status. The format of these registers is shown in Figure 18. Figure 18. Endpoint 0,1,2 Counter Registers (Addresses 0x11, 0x13 and 0x15) Bit # Bit Name Read/Writ e Reset 7 Data Toggle R/W 0 6 Data Valid R/W 0 5 4 3 2 1 0 de d fo rN ew D es Reserved 0 0 1 = The transaction completes with an ACK. en ig R/ W 0 ns R/ W 0 Bit 4: ACKed Transaction Byte Count R/ W 0 R/ W 0 USB Non-control Endpoints Figure 17. USB Endpoint EP1, EP2 Mode Registers (Addresses 0x14 and 0x16) ot R The CY7C637xxC feature two non-control endpoints, endpoint 1 (EP1) and endpoint 2 (EP2). The EP1 and EP2 Mode Registers do not have the locking mechanism of the EP0 Mode Register. The EP1 and EP2 Mode Registers use the format shown in Figure . EP1 uses an 8-byte FIFO at SRAM locations 0xF0-0xF7, EP2 uses an 8-byte FIFO at SRAM locations 0xE8-0xEF as shown in Section . ec om m 3 2 0 0 Bit 7: Data Toggle This bit selects the DATA packet's toggle state. For IN transactions, firmware must set this bit to the select the transmitted Data Toggle. For OUT or SETUP transactions, the hardware sets this bit to the state of the received Data Toggle bit. 1 = DATA1 0 = DATA0 Bit 6: Data Valid This bit is used for OUT and SETUP tokens only. This bit is cleared to `0' if CRC, bitstuff, or PID errors have occurred. This bit does not update for some endpoint mode settings. Refer to Table 10 for more details. 1 = Data is valid. 0 = Data is invalid. If enabled, the endpoint interrupt will occur even if invalid data is received. Bit STALL Reserved ACKed Name Transaction Read/ Write Reset R/W 0 0 0 R/C 0 N Bit # 7 6 5 4 1 0 Mode Bit R/W R/W R/W R/W 0 0 Document #: 38-08022 Rev. *D Page 19 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Bit [5:4]: Reserved Bit [3:0]: Byte Count Bit [3:0] Byte Count Bits indicate the number of data bytes in a transaction: For IN transactions, firmware loads the count with the number of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 8 inclusive. For OUT or SETUP transactions, the count is updated by hardware to the number of data bytes received, plus 2 for the CRC bytes. Valid values are 2 to 10 inclusive. For Endpoint 0 Count Register, whenever the count updates from a SETUP or OUT transaction, the count register locks and cannot be written by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on incoming SETUP or OUT transactions before firmware has a chance to read the data. even if the VREG Enable bit is cleared to 0. This insures proper USB signaling in the case where the VREG pin is used as an input, and an external regulator is provided for the USB pull-up resistor. This also limits the swing on the D- and D+ pins to about 1V above the internal regulator voltage, so the Device Address Enable bit normally should only be set for USB operating modes. The regulator output is only designed to provide current for the USB pull-up resistor. In addition, the output voltage at the VREG pin is effectively disconnected when the CY7C637xxC device transmits USB from the internal SIE. This means that the VREG pin does not provide a stable voltage during transmits, although this does not affect USB signaling. USB Regulator Output The VREG pin provides a regulated output for connecting the pull-up resistor required for USB operation. For USB, a 1.5-k resistor is connected between the D- pin and the VREG voltage, to indicate low-speed USB operation. Since the VREG output has an internal series resistance of approximately 200, the external pull-up resistor required is RPU (see Section ). The regulator output is placed in a high-impedance state at reset, and must be enabled by firmware by setting the VREG Enable bit in the USB Status and Control Register (Figure 14). This simplifies the design of a combination PS/2-USB device, since the USB pull-up resistor can be left in place during PS/2 operation without loading the PS/2 line. In this mode, the VREG pin can be used as an input and its state can be read at port P2.0. Refer to Figure for the Port 2 data register. This input has a TTL threshold. In suspend mode, the regulator is automatically disabled. If VREG Enable bit is set (Figure 14), the VREG pin is pulled up to VCC with an internal 6.2-k resistor. This holds the proper VOH state in suspend mode Note that enabling the device for USB (by setting the Device Address Enable bit, Figure 15) activates the internal regulator, om The CY7C637xxC parts are optimized for combination USB or PS/2 devices, through the following features: 1. USB D+ and D- lines can also be used for PS/2 SCLK and SDATA pins, respectively. With USB disabled, these lines can be placed in a high-impedance state that will pull up to VCC. (Disable USB by clearing the Address Enable bit of the USB Device Address Register, Figure 15). 2. An interrupt is provided to indicate a long LOW state on the SDATA pin. This eliminates the need to poll this pin to check for PS/2 activity. Refer to Section for more details. 3. Internal PS/2 pull-up resistors can be enabled on the SCLK and SDATA lines, so no GPIO pins are required for this task (bit 7, USB Status and Control Register, Figure 14). 4. The controlled slew rate outputs from these pins apply to both USB and PS/2 modes to minimize EMI. 5. The state of the SCLK and SDATA pins can be read, and can be individually driven LOW in an open drain mode. The pins are read at bits [5:4] of Port 2, and are driven with the Control Bits [2:0] of the USB Status and Control Register. 6. The VREG pin can be placed into a high-impedance state, so that a USB pull-up resistor on the D-/SDATA pin will not interfere with PS/2 operation (bit 6, USB Status and Control Register). The PS/2 on-chip support circuitry is illustrated in Figure 19. Document #: 38-08022 Rev. *D N ot R ec m en de d fo rN ew D es PS/2 Operation ig ns Page 20 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 19. Diagram of USB-PS/2 System Connections Port 2.0 VREG Enable 3.3V Regulator VCC PS/2 Pull-up Enable 5 k 5 k rN ew fo On-chip USB - PS/2 Driver Port 2.5 Port 2.4 Document #: 38-08022 Rev. *D N ot R ec om m en de d D es 1.3 k D+/SCLK D-/SDATA Off-chip Page 21 of 53 [+] Feedback ig ns 200 VREG CY7C63722C CY7C63723C CY7C63743C Serial Peripheral Interface (SPI) SPI is a four-wire, full-duplex serial communication interface between a master device and one or more slave devices. The CY7C637xxC SPI circuit supports byte serial transfers in either Master or Slave modes. The block diagram of the SPI circuit is shown in Figure 20. The block contains buffers for both transmit and receive data for maximum flexibility and throughput. The CY7C637xxC can be configured as either an SPI Master or Slave. The external interface consists of Master-Out/Slave-In (MOSI), Master-In/Slave-Out (MISO), Serial Clock (SCK), and Slave Select (SS). SPI modes are activated by setting the appropriate bits in the SPI Control Register, as described below. Figure 20. SPI Block Diagram Data Bus Write TX Buffer 8 bit shift register rN ew Master / Slave Control RX Buffer fo 4 d Data Bus en de Internal SCK Read m The SPI Data Register below serves as a transmit and receive buffer. from the SPI Data Register before the next byte of data is transferred to the receive buffer, or the data will be lost. When operating as a Master, an active LOW Slave Select (SS) must be generated to enable a Slave for a byte transfer. This Slave Select is generated under firmware control, and is not part of the SPI internal hardware. Any available GPIO can be used for the Master's Slave Select output. When the Master writes to the SPI Data Register, the data is loaded into the transmit buffer. If the shift register is not busy shifting a previous byte, the TX buffer contents will be automatically transferred into the shift register and shifting will begin. If the shift register is busy, the new byte will be loaded into the shift register only after the active byte has finished and is transferred to the receive buffer. The new byte will then be shifted out. The Transmit Buffer Full (TBF) bit will be set HIGH until the transmit buffer's data-byte is transferred to the shift register. Writing to the transmit buffer while the TBF bit is HIGH will overwrite the old byte in the transmit buffer. The byte shifting and SCK generation are handled by the hardware (based on firmware selection of the clock source). Data is shifted out on the MOSI pin (P0.5) and the serial clock is output on the SCK pin (P0.7). Data is received from the slave on the MISO pin (P0.6). The output pins must be set to the desired drive strength, and the GPIO data register must be set to 1 to enable a bypass mode for these pins. The MISO pin must be configured in the desired GPIO input mode. See Section for GPIO configuration details. Page 22 of 53 Bit Name Reset 0 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W ec om Bit # 7 6 5 4 3 2 1 0 Data I/O 0 0 0 0 0 0 Bit [7:0]: Data I/O[7:0] Writes to the SPI Data Register load the transmit buffer, while reads from this register read the receive buffer contents. 0 = Logic LOW Operation as an SPI Master Only an SPI Master can initiate a byte/data transfer. This is done by the Master writing to the SPI Data Register. The Master shifts out 8 bits of data (MSB first) along with the serial clock SCK for the Slave. The Master's outgoing byte is replaced with an incoming one from a Slave device. When the last bit is received, the shift register contents are transferred to the receive buffer and an interrupt is generated. The receive data must be read Document #: 38-08022 Rev. *D N 1 = Logic HIGH ot R Figure 21. SPI Data Register (Address 0x60) D es SS ig MOSI MISO SCK [+] Feedback ns CY7C63722C CY7C63723C CY7C63743C Master SCK Selection The Master's SCK is programmable to one of four clock settings, as shown in Figure 20. The frequency is selected with the Clock Select Bits of the SPI control register. The hardware provides 8 output clocks on the SCK pin (P0.7) for each byte transfer. Clock phase and polarity are selected by the CPHA and CPOL control bits (see Figure 20 and 23). The master SCK duty cycle is nominally 33% in the fastest (2 Mbps) mode, and 50% in all other modes. SPI Status and Control The SPI Control Register is shown in Figure 22. The timing diagram in Figure 23 shows the clock and data states for the various SPI modes. Figure 22. SPI Control Register (Address 0x61) Bit # 7 6 5 4 3 2 1 0 Bit Name TCMP TBF en In Slave mode, writes to the SPI Data Register load the Transmit buffer. If the Slave Select is asserted (SS LOW) and the shift register is not busy shifting a previous byte, the transmit buffer contents will be automatically transferred into the shift register. If the shift register is busy, the new byte will be loaded into the shift register only after the active byte has finished and is transferred to the receive buffer. The new byte is then ready to be shifted out (shifting waits for SCK from the Master). If the Slave Select is not active when the transmit buffer is loaded, data is not transferred to the shift register until Slave Select is asserted. The Transmit Buffer Full (TBF) bit will be set to `1' until the transmit buffer's data-byte is transferred to the shift register. Writing to the transmit buffer while the TBF bit is HIGH will overwrite the old byte in the Transmit Buffer. If the Slave Select is deasserted before a byte transfer is complete, the transfer is aborted and no interrupt is generated. Whenever Slave Select is asserted, the transmit buffer is automatically reloaded into the shift register. Bit 6: TBF de d m om Clock phase and polarity must be selected to match the SPI master, using the CPHA and CPOL control bits (see Figure 22 and Figure 23). The SPI slave logic continues to operate in suspend, so if the SPI interrupt is enabled, the device can go into suspend during a SPI slave transaction, and it will wake up at the interrupt that signals the end of the byte transfer. ec ot R N Document #: 38-08022 Rev. *D fo Bit [5:4] Comm Mode[1:0] 00 = All communications functions disabled (default). 01 = SPI Master Mode. 10 = SPI Slave Mode. 11 = Reserved. Bit 3: CPOL SPI Clock Polarity bit. 1 = SCK idles HIGH. 0 = SCK idles LOW. Bit 2: CPHA SPI Clock Phase bit (see Figure 23) Bit [1:0]: SCK Select Master mode SCK frequency selection (no effect in Slave Mode): 00 = 2 Mbit/s 01 = 1 Mbit/s 10 = 0.5 Mbit/s 11 = 0.0625 Mbit/s rN ew In slave mode, the chip receives SCK from an external master on pin P0.7. Data from the master is shifted in on the MOSI pin (P0.5), while data is being shifted out of the slave on the MISO pin (P0.6). In addition, the active LOW Slave Select must be asserted to enable the slave for transmit. The Slave Select pin is P0.4. These pins must be configured in appropriate GPIO modes, with the GPIO data register set to 1 to enable bypass mode selected for the MISO pin. Bit 7: TCMP 1 = TCMP is set to 1 by the hardware when 8-bit transfer is complete. The SPI interrupt is asserted at the same time TCMP is set to 1. 0 = This bit is only cleared by firmware. Transmit Buffer Full bit. 1 = Indicates data in the transmit buffer has not transferred to the shift register. 0 = Indicates data in the transmit buffer has transferred to the shift register. D es Reset 0 0 0 ig 0 0 Operation as an SPI Slave Comm CPOL CPHA SCK Mode[1:0] Select R/W R/W R/W 0 0 0 Read/Write R/W R/W R/W R/W R/W ns Page 23 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 23. SPI Data Timing SCK (CPOL = 0) SCK (CPOL = 1) SS Data Capture Strobe Interrupt Issued CPHA = 1: MOSI/MISO D es LSB GPIO Pin MSB Data Capture Strobe Interrupt Issued SPI Interrupt For SPI, an interrupt request is generated after a byte is received or transmitted. See Section for details on the SPI interrupt. SPI Modes for GPIO Pins The GPIO pins used for SPI outputs (P0.5-P0.7) contain a bypass mode, as shown in the GPIO block diagram (Figure ). Whenever the SPI block is inactive (Mode[5:4] = 00), the bypass value is 1, which enables normal GPIO operation. When SPI Table 5. SPI Pin Assignments SPI Function Slave Select (SS) Master Out, Slave In (MOSI) Master In, Slave Out (MISO) SCK P0.4 en de d fo master or slave modes are activated, the appropriate bypass signals are driven by the hardware for outputs, and are held at 1 for inputs. Note that the corresponding data bits in the Port 0 Data Register must be set to 1 for each pin being used for an SPI output. In addition, the GPIO modes are not affected by operation of the SPI block, so each pin must be programmed by firmware to the desired drive strength mode. For GPIO pins that are not used for SPI outputs, the SPI bypass value in Figure is always 1, for normal GPIO operation. m For master mode, firmware sets SS, may use any GPIO pin. For Slave Mode, SS is an active LOW input. Data output for master, data input for slave. om P0.5 P0.6 P0.7 Data input for master, data output for slave. SPI Clock: Output for master, input for slave. Document #: 38-08022 Rev. *D N ot R ec rN ew Comment ig x Page 24 of 53 [+] Feedback ns CPHA = 0: MOSI/MISO x MSB LSB CY7C63722C CY7C63723C CY7C63743C 12-bit Free-running Timer The 12-bit timer operates with a 1-s tick, provides two interrupts (128-s and 1.024-ms) and allows the firmware to directly time events that are up to 4 ms in duration. The lower eight bits of the timer can be read directly by the firmware. Reading the lower eight bits latches the upper four bits into a temporary register. When the firmware reads the upper four bits of the timer, it is actually reading the count stored in the temporary register. The effect of this is to ensure a stable 12-bit timer value can be read, even when the two reads are separated in time. Figure 24. Timer LSB Register (Address 0x24) Bit [7:4]: Reserved Bit # Bit Name Read/Write Reset R 0 R 0 R 0 7 6 5 4 R 0 3 R 0 2 R 0 1 R 0 0 R 0 Timer [7:0] Bit [7:0]: Timer lower eight bits Figure 25. Timer MSB Register (Address 0x25) Bit # Bit Name Read/Write Reset 0 7 6 0 5 0 4 0 3 R 0 2 R 0 1 R 0 0 R 0 Reserved Timer [11:8] Bit [3:0]: Timer upper four bits Figure 26. Timer Block Diagram rN ew 2 1 0 D3 D2 D1 8 D0 11 10 9 8 7 6 de 5 d 4 fo 3 D3 D2 om D1 m L3 L2 L1 L0 D0 en D7 D6 D5 D4 Document #: 38-08022 Rev. *D N ot R ec D es 1.024-ms interrupt 128-s interrupt 1 MHz clock To Timer Registers Page 25 of 53 [+] Feedback ig ns CY7C63722C CY7C63723C CY7C63743C Timer Capture Registers Four 8-bit capture timer registers provide both rising- and falling-edge event timing capture on two pins. Capture Timer A is connected to Pin 0.0, and Capture Timer B is connected to Pin 0.1. These can be used to mark the time at which a rising or falling event occurs at the two GPIO pins. Each timer will capture eight bits of the free-running timer into its Capture Timer Data Register if a rising or falling edge event that matches the specified rising or falling edge condition at the pin. A prescaler allows selection of the capture timer tick size. Interrupts can be individually enabled for the four capture registers. A block diagram is shown in Figure . First Edge Hold Bit 7, Reg 0x44 GPIO P0.0 de Falling Edge Detect Rising Edge Detect Falling Edge Detect d m GPIO P0.1 en Capture A Rising Int Enable om fo Rising Edge Detect Capture A Falling Int Enable Bit 1, Reg 0x44 ot R Capture B Rising Int Enable Bit 2, Reg 0x44 ec Bit 0, Reg 0x44 Document #: 38-08022 Rev. *D N Capture B Falling Int Enable Bit 3, Reg 0x44 rN ew Prescaler Mux 8-bit Capture Registers Timer A Rising Edge Time Timer A Falling Edge Time Timer B Rising Edge Time Timer B Falling Edge Time Capture Timer A Interrupt Request Capture Timer B Interrupt Request D es 11 10 9 8 7 6 5 4 3 2 1 0 ig Free-running Timer ns 1 MHz Clock Page 26 of 53 [+] Feedback Figure 27. Capture Timers Block Diagram CY7C63722C CY7C63723C CY7C63743C The four Capture Timer Data Registers are read-only, and are shown in Figure through Figure 30. Out of the 12-bit free running timer, the 8-bit captured in the Capture Timer Data Registers are determined by the Prescale Bit [2:0] in the Capture Timer Configuration Register (Figure 32). Capture Timer A-Rising, Data Register (Address 0x40.) Figure 31. Capture Timer Status Register (Address 0x45) Bit # Bit Name 7 6 5 4 3 2 1 0 Reserved Bit # Bit Name Read/Write Reset 7 R 0 6 R 0 5 R 0 4 R 0 3 R 0 2 R 0 1 R 0 0 R 0 Capture A Rising Data Read/ Write Reset 0 0 0 0 Capture Capture Capture Capture B B A A Falling Rising Falling Rising Event Event Event Event R 0 R 0 ns R 0 2 1 R/W 0 R/W 0 R 0 Figure 28. Capture Timer A-Falling, Data Register (Address 0x41) Bit [7:4]: Reserved. Bit # Bit Name Read/Write Reset R 0 R 0 7 6 5 R 0 4 R 0 3 R 0 2 R 0 1 R 0 0 R 0 Bit [3:0]: Capture A/B, Falling/Rising Event Capture A Falling Data Figure 29. Capture Timer B-Rising, Data Register (Address 0x42) de Bit # Bit Name Read/Write Reset 7 R 0 6 R 0 5 R 0 4 R 0 3 R 0 2 R 0 1 Capture B Rising Data en R 0 R 0 d 0 fo Bit # Figure 32. Capture Timer Configuration Register (Address 0x44) 7 6 5 4 3 0 m Figure 30. Capture Timer B-Falling, Data Register (Address 0x43) ec Bit First Prescale Bit Capture Capture Capture Capture Name Edge [2:0] B B A A Hold Falling Rising Falling Rising Int Int Int Int Enable Enable Enable Enable Read/ R/W R/W R/W R/W Write Reset 0 0 0 0 R/W 0 R/W 0 Bit # Bit Name Reset Read/Write 7 R 0 6 om 5 4 3 R 0 2 R 0 1 R 0 0 R 0 ot R Capture B Falling Data R 0 R 0 R 0 Document #: 38-08022 Rev. *D N rN ew These bits record the occurrence of any rising or falling edges on the capture GPIO pins. Bits in this register are cleared by reading the corresponding data register. 1 = A rising or falling event that matches the pin's rising/falling condition has occurred. 0 = No event that matches the pin's rising or falling edge condition. Because both Capture A events (rising and falling) share an interrupt, user's firmware needs to check the status of both Capture A Falling and Rising Event bits to determine what caused the interrupt. This is also true for Capture B events. D es ig Page 27 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Bit 7: First Edge Hold 1 = The time of the first occurrence of an edge is held in the Capture Timer Data Register until the data is read. Subsequent edges are ignored until the Capture Timer Data Register is read. 0 = The time of the most recent edge is held in the Capture Timer Data Register. That is, if multiple edges have occurred before reading the capture timer, the time for the last one will be read (default state). The First Edge Hold function applies globally to all four capture timers. Bit [6:4]: Prescale Bit [2:0] Three prescaler bits allow the capture timer clock rate to be selected among 5 choices, as shown in Table 6 below. Bit [3:0]: Capture A/B, Rising/Falling Interrupt Enable Each of the four Capture Timer registers can be individually enabled to provide interrupts. Both Capture A events share a common interrupt request, as do the two Capture B events. In addition to the event enables, the main Capture Interrupt Enables bit in the Global Interrupt Enable register (Section ) must be set to activate a capture interrupt. 1 = Enable interrupt 0 = Disable interrupt Table 6. Capture Timer Prescalar Settings (Step size and range for FCLK = 6 MHz) Captured Bits ig Prescale 2:0 000 001 010 011 100 D es Bits 7:0 of free-running timer Bits 8:1 of free-running timer Bits 9:2 of free-running timer rN ew Bits 10:3 of free-running timer Bits 11:4 of free-running timer Document #: 38-08022 Rev. *D N ot R ec om m en de d fo ns LSB Step Size 1 s 2 s 4 s 8 s 16 s Range 256 s 512 s 1.024 ms 2.048 ms 4.096 ms Page 28 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Processor Status and Control Register Figure 33. Processor Status and Control Register (Address 0xFF) Bit # Bit Name 7 IRQ Pending R 0 6 Watchdog Reset R/W 1 5 Bus Interrupt Event R/W 0 4 LVR/BOR Reset R/W 1 3 Suspend 2 Interrupt Enable Sense R 0 1 Reserved 0 Run Read/Write Reset R/W 0 ig 0 Bit 7: IRQ Pending When an interrupt is generated, it is registered as a pending interrupt. The interrupt will remain pending until its interrupt enable bit is set (Figure and Figure ) and interrupts are globally enabled (Bit 2, Processor Status and Control Register). At that point the internal interrupt handling sequence will clear the IRQ Pending bit until another interrupt is detected as pending. This bit is only valid if the Global Interrupt Enable bit is disabled. 1 = There are pending interrupts. 0 = No pending interrupts. Bit 6: Watchdog Reset affected by WDR. Note that a LVR/BOR event may be followed by a Watchdog reset before firmware begins executing, as explained at the end of this section. Bit 3: Suspend en The Watchdog Timer Reset (WDR) occurs when the internal Watchdog timer rolls over. The timer will roll over and WDR will occur if it is not cleared within tWATCH (see Section for the value of tWATCH). This bit is cleared by an LVR/BOR. Note that a Watchdog reset can occur with a POR/LVR/BOR event, as discussed at the end of this section. de d m 1 = A Watchdog reset occurs. 0 = No Watchdog reset Bit 5: Bus Interrupt Event om ot R The Bus Reset Status is set whenever the event for the USB Bus Reset or PS/2 Activity interrupt occurs. The event type (USB or PS/2) is selected by the state of the USB-PS/2 Interrupt Mode bit in the USB Status and Control Register (see Figure 14). The details on the event conditions that set this bit are given in Section . In either mode, this bit is set as soon as the event has lasted for 128-256 s, and the bit will be set even if the interrupt is not enabled. The bit is only cleared by firmware or LVR/WDR. ec 1 = A USB reset occurred or PS/2 Activity is detected, depending on USB-PS/2 Interrupt Select bit. N 0 = No event detected since last cleared by firmware or LVR/WDR. Bit 4: LVR/BOR Reset The Low-voltage or Brown-out Reset is set to `1' during a power-on reset. Firmware can check bits 4 and 6 in the reset handler to determine whether a reset was caused by a LVR/BOR condition or a Watchdog timeout. This bit is not Document #: 38-08022 Rev. *D fo Bit 2: Interrupt Enable Sense This bit shows whether interrupts are enabled or disabled. Firmware has no direct control over this bit as writing a zero or one to this bit position will have no effect on interrupts. This bit is further gated with the bit settings of the Global Interrupt Enable Register (Figure ) and USB Endpoint Interrupt Enable Register (Figure ). Instructions DI, EI, and RETI manipulate the state of this bit. 1 = Interrupts are enabled. 0 = Interrupts are masked off. Bit 1: Reserved. Must be written as a 0. Bit 0: Run This bit is manipulated by the HALT instruction. When Halt is executed, the processor clears the run bit and halts at the end of the current instruction. The processor remains halted until a reset occurs (low-voltage, brown-out, or Watchdog). This bit should normally be written as a `1'. rN ew 1 = A POR or LVR has occurred. 0 = No POR nor LVR since this bit last cleared. Writing a '1' to the Suspend bit will halt the processor and cause the microcontroller to enter the suspend mode that significantly reduces power consumption. An interrupt or USB bus activity will cause the device to come out of suspend. After coming out of suspend, the device will resume firmware execution at the instruction following the IOWR which put the part into suspend. When writing the suspend bit with a resume condition present (such as non-idle USB activity), the suspend state will still be entered, followed immediately by the wake-up process (with appropriate delays for the clock start-up). See Section for more details on suspend mode operation. 1 = Suspend the processor. 0 = Not in suspend mode. Cleared by the hardware when resuming from suspend. D es ns - R/W 1 Page 29 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C During power-up, or during a low-voltage reset, the Processor Status and Control Register is set to 00010001, which indicates a LVR/BOR (bit 4 set) has occurred and no interrupts are pending (bit 7 clear). Note that during the tSTART ms partial suspend at start-up (explained in Section ), a Watchdog Reset will also occur. When a WDR occurs during the power-up suspend interval, firmware would read 01010001 from the Status and Control Register after power-up. Normally the LVR/BOR bit should be cleared so that a subsequent WDR can be clearly identified. Note that if a USB bus reset (long SE0) is received before firmware examines this register, the Bus Interrupt Event bit would also be set. During a Watchdog Reset, the Processor Status and Control Register is set to 01XX0001, which indicates a Watchdog Reset (bit 4 set) has occurred and no interrupts are pending (bit 7 clear). are restored and interrupts are enabled when the RETI instruction is executed. The DI and EI instructions can be used to disable and enable interrupts, respectively. These instructions affect only the Global Interrupt Enable bit of the CPU. If desired, EI can be used to re-enable interrupts while inside an ISR, instead of waiting for the RETI that exits the ISR. While the global interrupt enable bit is cleared, the presence of a pending interrupt can be detected by examining the IRQ Sense bit (Bit 7 in the Processor Status and Control Register). Interrupts Interrupts can be generated by the GPIO lines, the internal free-running timer, the SPI block, the capture timers, on various USB events, PS/2 activity, or by the wake-up timer. All interrupts are maskable by the Global Interrupt Enable Register and the USB End Point Interrupt Enable Register. Writing a `1' to a bit position enables the interrupt associated with that bit position. During a reset, the contents of the interrupt enable registers are cleared, along with the Global Interrupt enable bit of the CPU, effectively disabling all interrupts. Table 7. Interrupt Vector Assignments Interrupt Vector No. ROM Address 0x0000 Function Execution after Reset begins here USB Bus Reset or PS/2 Activity interrupt 128-s timer interrupt 1.024-ms timer interrupt USB Endpoint 0 interrupt USB Endpoint 1 interrupt USB Endpoint 2 interrupt SPI Interrupt Capture Timer A interrupt Capture Timer B interrupt GPIO interrupt Wake-up Timer interrupt fo m The interrupt controller contains a separate flip-flop for each interrupt. See Figure 36 for the logic block diagram of the interrupt controller. When an interrupt is generated it is first registered as a pending interrupt. It will stay pending until it is serviced or a reset occurs. A pending interrupt will only generate an interrupt request if it is enabled by the corresponding bit in the interrupt enable registers. The highest priority interrupt request will be serviced following the completion of the currently executing instruction. d de en ot R When servicing an interrupt, the hardware will first disable all interrupts by clearing the Global Interrupt Enable bit in the CPU (the state of this bit can be read at Bit 2 of the Processor Status and Control Register). Next, the flip-flop of the current interrupt is cleared. This is followed by an automatic CALL instruction to the ROM address associated with the interrupt being serviced (i.e., the Interrupt Vector, see Section ). The instruction in the interrupt table is typically a JMP instruction to the address of the Interrupt Service Routine (ISR). The user can re-enable interrupts in the interrupt service routine by executing an EI instruction. Interrupts can be nested to a level limited only by the available stack space. om ec Interrupt Latency Interrupt latency can be calculated from the following equation: Interrupt Latency = (Number of clock cycles remaining in the current instruction) + (10 clock cycles for the CALL instruction) + (5 clock cycles for the JMP instruction) For example, if a 5 clock cycle instruction such as JC is being executed when an interrupt occurs, the first instruction of the Interrupt Service Routine will execute a minimum of 16 clocks (1+10+5) or a maximum of 20 clocks (5+10+5) after the interrupt is issued. With a 6-MHz external resonator, internal CPU clock speed is 12 MHz, so 20 clocks take 20/12 MHz = 1.67 s. The Program Counter value as well as the Carry and Zero flags (CF, ZF) are stored onto the Program Stack by the automatic CALL instruction generated as part of the interrupt acknowledge process. The user firmware is responsible for ensuring that the processor state is preserved and restored during an interrupt. The PUSH A instruction should typically be used as the first command in the ISR to save the accumulator value and the POP A instruction should be used just before the RETI instruction to restore the accumulator value. The program counter, CF and ZF Document #: 38-08022 Rev. *D N rN ew not applicable 1 2 3 4 5 6 7 8 9 10 11 0x0002 0x0004 0x0006 0x0008 0x000A 0x000E 0x0010 0x0012 0x0014 0x0016 The Interrupt Vectors supported by the device are listed in Table 7. The highest priority interrupt is #1 (USB Bus Reset / PS/2 activity), and the lowest priority interrupt is #11 (Wake-up Timer). Although Reset is not an interrupt, the first instruction executed after a reset is at ROM address 0x0000, which corresponds to the first entry in the Interrupt Vector Table. Interrupt vectors occupy two bytes to allow for a two-byte JMP instruction to the appropriate Interrupt Service Routine (ISR). 0x000C D es ig Interrupt Vectors ns Page 30 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Interrupt Sources The following sections provide details on the different types of interrupt sources. Figure 34. Global Interrupt Enable Register (Address 0x20) Bit # Bit Name 7 Wake-up Interrupt Enable R/W 0 6 GPIO Interrupt Enable R/W 0 5 Capture Timer B Intr. Enable R/W 0 4 Capture Timer A Intr. Enable R/W 0 3 SPI Interrupt Enable R/W 0 2 1.024-ms Interrupt Enable R/W 0 1 128-s Interrupt Enable R/W 0 0 USB Bus Reset / PS/2 Activity Intr. Enable R/W 0 Read/Write Reset Bit 7: Wake-up Interrupt Enable The internal wake-up timer is normally used to wake the part from suspend mode, but it can also provide an interrupt when the part is awake. The wake-up timer is cleared whenever the Wake-up Interrupt Enable bit is written to a 0, and runs whenever that bit is written to a 1. When the interrupt is enabled, the wake-up timer provides periodic interrupts at multiples of period, as described in Section . 1 = Enable wake-up timer for periodic wake-up. 0 = Disable and power-off wake-up timer. Bit 6: GPIO Interrupt Enable Bit [5:4]: Capture Timer A and B Interrupts m Each GPIO pin can serve as an interrupt input. During a reset, GPIO interrupts are disabled by clearing all GPIO interrupt enable registers. Writing a `1' to a GPIO Interrupt Enable bit enables GPIO interrupts from the corresponding input pin. These registers are shown in Figure 37 for Port 0 and Figure 38 for Port 1. In addition to enabling the desired individual pins for interrupt, the main GPIO interrupt must be enabled, as explained in Section . en de d ec The polarity that triggers an interrupt is controlled independently for each GPIO pin by the GPIO Interrupt Polarity Registers. Setting a Polarity bit to `0' allows an interrupt on a falling GPIO edge, while setting a Polarity bit to `1' allows an interrupt on a rising GPIO edge. The Polarity Registers reset to 0 and are shown in Figure 39 for Port 0 and Figure for Port 1. om ot R All of the GPIO pins share a single interrupt vector, which means the firmware will need to read the GPIO ports with enabled interrupts to determine which pin or pins caused an interrupt.The GPIO interrupt structure is illustrated in Figure . Note that if one port pin triggered an interrupt, no other port pins can cause a GPIO interrupt until that port pin has returned to its inactive (non-trigger) state or its corresponding port interrupt enable bit is cleared. The CY7C637xxC does not assign interrupt priority to different port pins and the Port Interrupt Enable Registers are not affected by the interrupt acknowledge process. N 1 = Enable 0 = Disable Document #: 38-08022 Rev. *D fo Bit 3: SPI Interrupt Enable The SPI interrupt occurs at the end of each SPI byte transaction, at the final clock edge, as shown in Figure 23. After the interrupt, the received data byte can be read from the SPI Data Register, and the TCMP control bit will be high 1 = Enable 0 = Disable Bit 2: 1.024-ms Interrupt Enable The 1.024-ms interrupts are periodic timer interrupts from the free-running timer (based on the 6-MHz clock). The user should disable this interrupt before going into the suspend mode to avoid possible conflicts between servicing the timer interrupts (128-s interrupt and 1.024-ms interrupt) first or the suspend request first when waking up. 1 = Enable. Periodic interrupts will be generated approximately every 1.024 ms. 0 = Disable. Bit 1: 128-s Interrupt Enable The 128-s interrupt is another source of timer interrupt from the free-running timer. The user should disable both timer interrupts (128-s and 1.024-ms) before going into the suspend mode to avoid possible conflicts between servicing the timer interrupts first or the suspend request first when waking up. 1 = Enable. Periodic interrupts will be generated approximately every 128 s. 0 = Disable. rN ew 1 = Enable 0 = Disable There are two capture timer interrupts, one for each associated pin. Each of these interrupts occurs on an enabled edge of the selected GPIO pin(s). For each pin, rising and/or falling edge capture interrupts can be in selected. Refer to Section . These interrupts are independent of the GPIO interrupt, described in the next section. D es ig ns Page 31 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Bit 0: USB Bus Reset - PS/2 Interrupt Enable The function of this interrupt is selectable between detection of either a USB bus reset condition, or PS/2 activity. The selection is made with the USB-PS/2 Interrupt Mode bit in the USB Status and Control Register (Figure 14). In either case, the interrupt will occur if the selected condition exists for 256 s, and may occur as early as 128 s. A USB bus reset is indicated by a single ended zero (SE0) on the USB D+ and D- pins. The USB Bus Reset interrupt occurs when the SE0 condition ends. PS/2 activity is indicated by a continuous LOW on the SDATA pin. The PS/2 interrupt occurs as soon as the long LOW state is detected. During the entire interval of a USB Bus Reset or PS/2 interrupt event, the USB Device Address register is cleared. The Bus Reset/PS/2 interrupt may occur 128 s after the bus condition is removed. 1 = Enable 0 = Disable Figure 35. Endpoint Interrupt Enable Register (Address 0x21) Bit # Bit Name 76543 Reserved 2 EP2 Interrupt Enable R/W 0 1 EP1 Interrupt Enable R/W 0 0 EP0 Interrupt Enable R/W 0 Bit [2:1]: EP2,1 Interrupt Enable There are two non-control endpoint (EP2 and EP1) interrupts. If enabled, a non-control endpoint interrupt is generated when: The USB host writes valid data to an endpoint FIFO. However, if the endpoint is in ACK OUT modes, an interrupt is generated regardless of data packet validity (i.e., good CRC). Firmware must check for data validity. The device SIE sends a NAK or STALL handshake packet to the USB host during the host attempts to read data from the endpoint (INs). The device receives an ACK handshake after a successful read transaction (IN) from the host. The device SIE sends a NAK or STALL handshake packet to the USB host during the host attempts to write data (OUTs) to the endpoint FIFO. 1 = Enable 0 = Disable Refer to Table 8 for more information. Bit 0: EP0 Interrupt Enable If enabled, a control endpoint interrupt is generated when: The endpoint 0 mode is set to accept a SETUP token. After the SIE sends a 0-byte packet in the status stage of a control transfer. The USB host writes valid data to an endpoint FIFO. However, if the endpoint is in ACK OUT modes, an interrupt is generated regardless of what data is received. Firmware must check for data validity. The device SIE sends a NAK or STALL handshake packet to the USB host during the host attempts to read data from the endpoint (INs). The device SIE sends a NAK or STALL handshake packet to the USB host during the host attempts to write data (OUTs) to the endpoint FIFO. 1 = Enable EP0 interrupt Reset 00000 m Bit [7:3]: Reserved. en de Read/Write - - - - d Document #: 38-08022 Rev. *D N ot R ec om fo rN ew 0 = Disable EP0 interrupt D es ig ns Page 32 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 36. Interrupt Controller Logic Block Diagram USB-PS/2 Clear CLR 1 USBPS/2 Int D CLK Q Enable [0] (Reg 0x20) USB-PS/2 IRQ 128-s CLR 128-s IRQ 1-ms CLR 1-ms IRQ EP0 CLR EP0 IRQ EP1 CLR EP1 IRQ EP2 CLR EP2 IRQ SPI CLR SPI IRQ Interrupt Vector To CPU CLR 1 EP2 Int D CLK Q Enable [2] (Reg 0x21) Capture A CLR Capture A IRQ Capture B CLR Capture B IRQ GPIO CLR GPIO IRQ Wake-up CLR CLR rN ew Bit # Bit Name Read/Write Reset W 0 W 0 7 6 Interrupt Acknowledge D CLK Wake-up Int m en de Enable [7] (Reg 0x20) om Bit # Bit Name Read/Write Reset 7 W 0 6 W 0 5 4 3 2 1 W 0 0 W 0 d 1 Q Wake-up IRQ P0 Interrupt Enable W 0 W 0 W 0 0 W ec Figure 37. Port 0 Interrupt Enable Register (Address 0x04) Bit [7:0]: P0 [7:0] Interrupt Enable 1 = Enables GPIO interrupts from the corresponding input pin. 0 = Disables GPIO interrupts from the corresponding input pin. ot R fo Interrupt Priority Encoder Bit [7:0]: P1 [7:0] Interrupt Enable 1 = Enables GPIO interrupts from the corresponding input pin. 0 = Disables GPIO interrupts from the corresponding input pin. The polarity that triggers an interrupt is controlled independently for each GPIO pin by the GPIO Interrupt Polarity Registers. Figure 39 and Figure control the interrupt polarity of each GPIO pin. 5 W 0 4 W 0 3 W 0 2 W 0 1 W 0 0 W 0 N Bit # 7 W 0 6 W 0 5 W 0 4 W 0 3 W 0 2 W 0 1 W 0 0 W 0 Bit Name Read/Write Reset P1 Interrupt Enable Figure 39. Port 0 Interrupt Polarity Register (Address 0x06) Bit [7:0]: P0[7:0] Interrupt Polarity 1 = Rising GPIO edge 0 = Falling GPIO edge Figure 38. Port 1 Interrupt Enable Register (Address 0x05) Document #: 38-08022 Rev. *D D es Global Interrupt Enable Bit CLR Controlled by DI, EI, and RETI Instructions P0 Interrupt Polarity ig IRQout ns (Bit 7, Reg 0xFF) CPU IRQ Pending IRQ Int Enable Sense (Bit 2, Reg 0xFF) Page 33 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 40. Port 1 Interrupt Polarity Register (Address 0x07) Bit # Bit Name Read/Write Reset W 0 W 0 7 6 5 W 0 4 W 0 3 W 0 2 W 0 1 W 0 0 W Bit [7:0]: P1[7:0] Interrupt Polarity 1 = Rising GPIO edge 0 = Falling GPIO edge P1 Interrupt Polarity Figure 41. GPIO Interrupt Diagram Port Bit Interrupt Polarity Register GPIO Pin M U X rN ew OR Gate (1 input per GPIO pin) GPIO Interrupt Flip Flop 1 D Q D es Interrupt Priority Encoder IRQout Interrupt Vector CLR Document #: 38-08022 Rev. *D N ot R ec om m en de 1 = Enable 0 = Disable d IRA fo 1 = Enable 0 = Disable Port Bit Interrupt Enable Register Global GPIO Interrupt Enable (Bit 6, Register 0x20) ig Page 34 of 53 [+] Feedback ns 0 CY7C63722C CY7C63723C CY7C63743C USB Mode Tables The following tables give details on mode setting for the USB Serial Interface Engine (SIE) for both the control endpoint (EP0) and non-control endpoints (EP1 and EP2). Table 8. USB Register Mode Encoding for Control and Non-Control Endpoints Mode Disable NAK IN/OUT Encoding 0000 0001 SETUP Ignore Accept IN Ignore NAK OUT Ignore NAK Comments Ignore all USB traffic to this endpoint On Control endpoint, after successfully sending an ACK handshake to a SETUP packet, the SIE forces the endpoint mode (from modes other than 0000) to 0001. The mode is also changed by the SIE to 0001 from mode 1011 on issuance of ACK handshake to an OUT. For Control endpoints For Control endpoints For Control endpoints Reserved For Control Endpoints Reserved In mode 1001, after sending an ACK handshake to an OUT, the SIE changes the mode to 1000 This mode is changed by the SIE to mode 1000 on issuance of ACK handshake to an OUT This mode is changed by the SIE to mode 0001 on issuance of ACK handshake to an OUT An ACK from mode 1101 changes the mode to 1100 This mode is changed by the SIE to mode 1100 on issuance of ACK handshake to an IN An ACK from mode 1111 changes the mode to 1110 This mode is changed by the SIE to mode 1110 on issuance of ACK handshake to an IN m Note 3. STALL bit is the bit 7 of the USB Non-Control Device Endpoint Mode registers. Refer to Section for more explanation. en NAK IN ACK IN(STALL[3]=0) ACK IN(STALL[3]=1) NAK IN - Status OUT ACK IN - Status OUT 1100 1101 1101 1110 1111 Ignore Ignore Ignore Accept Accept NAK TX Count STALL NAK TX Count Ignore Ignore Ignore Check Check de Mode Column: ec The 'Mode' column contains the mnemonic names given to the modes of the endpoint. The mode of the endpoint is determined by the four-bit binaries in the 'Encoding' column as discussed below. The Status IN and Status OUT modes represent the status IN or OUT stage of the control transfer. The contents of the 'Encoding' column represent the Mode Bits [3:0] of the Endpoint Mode Registers (Figure 16 and Figure ). The endpoint modes determine how the SIE responds to different tokens that the host sends to the endpoints. For example, if the Mode Bits [3:0] of the Endpoint 0 Mode Register (Figure 16) are set to '0001', which is NAK IN/OUT mode as shown in Table 8 above, the SIE of the part will send an ACK handshake in response to SETUP tokens and NAK any IN or OUT tokens. For more information on the functionality of the Serial Interface Engine (SIE), see Section . om ot R Encoding Column: N SETUP, IN, and OUT Columns: Depending on the mode specified in the 'Encoding' column, the 'SETUP', 'IN', and 'OUT' columns contain the device SIE's responses when the endpoint receives SETUP, IN, and OUT tokens respectively. Document #: 38-08022 Rev. *D d fo ACK OUT(STALL[3]=0) ACK OUT(STALL[3]=1) NAK OUT - Status IN ACK OUT - NAK IN 1001 1001 1010 1011 Ignore Ignore Accept Accept Ignore Ignore TX 0 Byte NAK ACK STALL NAK ACK A 'Check' in the Out column means that upon receiving an OUT token the SIE checks to see whether the OUT is of zero length and has a Data Toggle (Data1/0) of 1. If these conditions are true, the SIE responds with an ACK. If any of the above conditions is not met, the SIE will respond with either a STALL or Ignore. Table 10 gives a detailed analysis of all possible cases. A 'TX Count' entry in the IN column means that the SIE will transmit the number of bytes specified in the Byte Count Bit [3:0] of the Endpoint Count Register (Figure 18) in response to any IN token. A 'TX 0 Byte' entry in the IN column means that the SIE will transmit a zero byte packet in response to any IN sent to the endpoint. Sending a 0 byte packet is to complete the status stage of a control transfer. An 'Ignore' means that the device sends no handshake tokens. An 'Accept' means that the SIE will respond with an ACK to a valid SETUP transaction. Comments Column: Some Mode Bits are automatically changed by the SIE in response to many USB transactions. For example, if the Mode Bits [3:0] are set to '1111' which is ACK IN-Status OUT mode as shown in Table 8, the SIE will change the endpoint Mode Bits Page 35 of 53 rN ew Status OUT Only STALL IN/OUT Ignore IN/OUT Reserved Status IN Only Reserved NAK OUT 0010 0011 0100 0101 0110 0111 1000 Accept Accept Accept Ignore Accept Ignore Ignore STALL STALL Ignore Ignore TX 0 Byte TX Count Ignore Check STALL Ignore Always STALL Ignore NAK D es ig ns [+] Feedback CY7C63722C CY7C63723C CY7C63743C [3:0] to NAK IN-Status OUT mode (1110) after ACKing a valid status stage OUT token. The firmware needs to update the mode for the SIE to respond appropriately. See Table 8 for more details on what modes will be changed by the SIE. Any SETUP packet to an enabled endpoint with mode set to accept SETUPs will be changed by the SIE to 0001 (NAKing). Any mode set to accept a SETUP will send an ACK handshake to a valid SETUP token. A disabled endpoint will remain disabled until changed by firmware, and all endpoints reset to the Disabled mode (0000). Firmware normally enables the endpoint mode after a SetConfiguration request. The control endpoint has three status bits for identifying the token type received (SETUP, IN, or OUT), but the endpoint must be placed in the correct mode to function as such. Non-control endpoints should not be placed into modes that accept SETUPs. Table 9. Decode table for Table 10: "Details of Modes for Differing Traffic Conditions" Endpoint Mode Encoding Properties of incoming packet Changes to the internal register made by the SIE as a result of the incoming token End Point Mode 2 1 D es ACK 3 0 rN ew Setup In Out 3 2 1 0 Token ig Interrupt? count buffer dval DTOG DVAL COUNT Response SIE's Response Endpoint Mode changed by the SIE. Int Bit[3:0], Figure 18 Data Valid (Bit 6, Figure 18) Data 0/1 (Bit 7, Figure 18) Received Token (SETUP, IN,OUT) The validity of the received data The quality status of the DMA buffer The number of received bytes fo Legend: UC: unchanged x: don't care TX: transmit RX: receive de d PID Status Bits (Bit[7:5], Figure 16) Acknowledge transaction completed (Bit4,Figure 16/3) TX0: transmit 0-length packet available for Control endpoint only Document #: 38-08022 Rev. *D N ot R ec om m en ns Page 36 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C The response of the SIE can be summarized as follows: 1. The SIE will only respond to valid transactions, and will ignore non-valid ones. 2. The SIE will generate an interrupt when a valid transaction is completed or when the FIFO is corrupted. FIFO corruption occurs during an OUT or SETUP transaction to a valid internal address, that ends with a non-valid CRC. 3. An incoming Data packet is valid if the count is < Endpoint Size + 2 (includes CRC) and passes all error checking; 4. An IN will be ignored by an OUT configured endpoint and visa versa. 5. The IN and OUT PID status is updated at the end of a transaction. Table 10. Details of Modes for Differing Traffic Conditions End Point Mode 3 2 1 Rcved 0 Token Cou nt <= 10 > 10 x Buffer Dval DTOG updates updates updates DVAL COUN T updates updates updates PID SETUP IN U C D es OU T ACK 3 UC 1 UC UC 0 UC UC UC UC 1 UC UC UC UC UC UC UC UC UC UC UC 1 UC UC UC UC UC UC UC 1 1 1 1 UC UC 0 6. The SETUP PID status is updated at the beginning of the Data packet phase. 7. The entire Endpoint 0 mode register and the Count register are locked to CPU writes at the end of any transaction to that endpoint in which an ACK is transferred. These registers are only unlocked by a CPU read of these registers, and only if that read happens after the transaction completes. This represents about a 1-s window in which the CPU is locked from register writes to these USB registers. Normally the firmware should perform a register read at the beginning of the Endpoint ISRs to unlock and get the mode register information. The interlock on the Mode and Count registers ensures that the firmware recognizes the changes that the SIE might have made during the previous transaction. ig NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e Set End Point Mode 2 1 0 Response Int ye s ye s ye s SETUP Packet (if accepting) See8 See8 See 8 Disabled 0 0 0 0x x UC x UC UC SETUP SETUP SETUP data junk junk valid x invalid 1 updates 0 rN ew 1 1 U C 1 U C UC U C fo de NAK IN/OUT 0 0 0 0 0 0 0 0 0 0 0 0 1 OUT 1 OUT 1 OUT 1 IN x > 10 x x UC UC UC UC x x d UC ns 0 0 1 ACK Ignore Ignore Ignore NAK Ignore Ignore NAK Ignore Ignore STALL Ignore Ignore STALL 0 0 1 ACK Ignore Ignore no UC UC UC UC UC UC UC UC UC UC UC U C U C U C 1 ye s no no ye s m x invalid Ignore IN/OUT 0 0 1 1 0 0 0 OUT 0 IN x x om en UC UC UC UC UC UC x UC UC UC UC UC UC UC UC U C U C no no ec UC x STALL IN/OUT 0 0 0 0 0 0 0 1 1 OUT ot R x UC UC UC UC x x invalid x UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC U C U C U C 1 ye s no no ye s 1 1 OUT > 10 x N 0 1 1 1 OUT 1 IN x Control Write ACK OUT/NAK IN 1 1 1 0 0 0 1 1 1 1 OUT 1 OUT 1 OUT <= 10 > 10 x data junk junk valid x invalid updates updates updates 1 updates 0 updates updates updates UC UC UC U C U C U C ye s ye s ye s Document #: 38-08022 Rev. *D Page 37 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Table 10. Details of Modes for Differing Traffic Conditions (continued) 1 0 1 1 IN x UC x UC UC UC UC 1 UC UC NoChang e NAK ye s NAK OUT/Status IN 1 1 1 1 0 0 0 0 1 1 1 1 0 OUT 0 OUT 0 OUT 0 IN <= 10 > 10 x x UC UC UC UC valid x invalid x UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC U C U C U C 1 1 UC UC UC UC UC UC 1 NoChang e NoChang e NoChang e NoChang e NAK Ignore Ignore ye s no no ye s Status IN Only 0 0 0 0 1 1 1 1 1 1 1 1 0 OUT 0 OUT 0 OUT 0 IN <= 10 > 10 x x UC UC UC UC valid x invalid x UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC U C U C U C 1 UC D es 0 UC UC UC UC 1 UC 1 1 UC UC UC UC 1 1 1 UC UC UC 0 0 1 1 1 OU T 1 UC UC UC 1 UC ACK UC UC UC UC 0 3 0 1 1 1 UC UC UC 1 UC UC UC UC UC 0 0 0 ig NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e ns TX 0 Byte 0 1 1 STALL Ignore Ignore TX 0 Byte ACK 0 1 1 STALL 0 1 1 STALL Ignore Ignore ACK 1 1 0 (back) ACK 0 1 1 STALL 2 1 0 response 0 1 1 STALL Ignore Ignore NAK ACK 0 1 1 STALL 0 1 1 STALL Ignore Ignore 0 1 1 STALL ye s no no ye s Control Read ACK IN/Status OUT 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 OUT 1 OUT 1 OUT 1 OUT 1 OUT 1 IN 2 2 !=2 > 10 x x UC UC UC UC UC UC valid valid valid x invalid x 1 0 updates UC 1 1 1 updates updates rN ew UC 1 U C UC ye s ye s ye s no no ye s fo updates UC UC UC updates updates COUN T updates UC UC UC UC U C U C U C U C 1 de UC UC UC d UC UC UC UC UC UC m NAK IN/Status OUT 1 1 3 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 0 OUT 0 OUT 0 token 0 OUT 0 OUT 2 2 UC UC en valid 1 1 1 DVAL 1 UC UC UC UC UC SETUP UC UC UC UC U C U C IN U C U C U C 1 ye s ye s int ye s no no ye s om valid dval buffer UC valid x invalid x UC UC UC 0 DTOG updates UC UC UC coun t !=2 Status OUT Only 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 OUT 0 OUT 0 OUT 0 OUT 0 OUT 0 IN 2 2 !=2 > 10 x x UC UC UC UC UC UC valid valid valid x invalid x 1 0 updates UC UC UC 1 1 1 UC UC UC updates updates updates UC UC UC UC UC UC UC UC UC U C U C U C U C U C 1 ye s ye s ye s no no ye s Document #: 38-08022 Rev. *D N ot R > 10 x 1 0 OUT 1 0 IN x ec Page 38 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Table 10. Details of Modes for Differing Traffic Conditions (continued) OUT Endpoint ACK OUT, STALL Bit = 0 (Figure ) 1 1 1 1 0 0 0 0 0 0 0 0 1 OUT 1 OUT 1 OUT 1 IN <= 10 > 10 x x data junk junk UC valid x invalid x updates updates updates UC 1 updates 0 UC updates updates updates UC UC UC UC UC U C U C U C U C 1 1 1 UC 1 UC UC UC 1 0 0 0 ACK Ignore Ignore ye s ye s ye s no NoChang e NoChang e NoChang e ACK OUT, STALL Bit = 1 (Figure ) 1 1 1 1 0 0 0 0 0 0 0 0 1 OUT 1 OUT 1 OUT 1 IN <= 10 > 10 x x UC UC UC UC valid x invalid x UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC U C U C U C U C 1 UC ig NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e 1 NoChang e NoChang e NoChang e NoChang e NoChang e NoChang e ns Ignore STALL Ignore Ignore Ignore NAK Ignore Ignore Ignore RX Ignore Ignore ACK 1 0 0 (back) Ignore STALL Ignore NAK Ignore TX D es UC UC UC UC UC UC 1 UC UC UC UC UC UC UC 1 UC 1 UC UC UC UC 1 UC UC UC UC UC UC UC UC UC UC UC UC ye s no no no NAK OUT 1 1 1 1 0 0 0 0 0 0 0 0 0 OUT 0 OUT 0 OUT 0 IN <= 10 > 10 x x UC UC UC UC valid x invalid x UC UC UC UC UC UC UC UC rN ew U C UC UC ye s no no no UC UC U C fo UC UC updates UC UC U C U C 0 0 1 1 0 0 1 OUT 1 IN x x updates UC updates x updates UC de updates UC Reserved d UC UC UC U C U C ye s no IN Endpoint ACK IN, STALL Bit = 0 (Figure ) 1 1 1 1 0 0 1 OUT 1 IN x x UC m en om x UC UC UC UC UC UC UC UC U C 1 no ye s UC x ec ACK IN, STALL Bit = 1 (Figure ) 1 1 1 1 0 0 1 OUT 1 IN x UC x x UC UC UC UC UC UC UC UC U C 1 no ye s ot R x UC NAK IN 1 1 1 1 0 0 OUT x UC UC x x UC UC UC UC UC UC UC UC U C 1 no ye s N 0 0 IN x Reserved 0 0 1 1 1 1 1 Out 1 IN x x UC UC x x UC UC UC UC UC UC UC UC U C 1 no ye s Document #: 38-08022 Rev. *D Page 39 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Register Summary Address 0x00 GPIO CONFIGURATION PORTS 0, 1 AND 2 0x01 0x02 0x0A 0x0B 0x0C 0x0D 0x04 0x05 0x06 0x07 0xF8 Clock Config. Register Name Port 0 Data Port 1 Data Port 2 Data GPIO Port 0 Mode 0 GPIO Port 0 Mode 1 GPIO Port 1 Mode 0 GPIO Port 1 Mode 1 Port 0 Interrupt Enable Port 1 Interrupt Enable Port 0 Interrupt Polarity Port 1 Interrupt Polarity Clock Configuration Ext. Clock Resume Delay Reserved D+(SCLK) State Bit 7 Bit 6 Bit 5 Bit 4 P0 P1 D- (SDATA) State P0[7:0] Mode0 P0[7:0] Mode1 P1[7:0] Mode0 P1[7:0] Mode1 P0[7:0] Interrupt Enable P1[7:0] Interrupt Enable P0[7:0] Interrupt Polarity P1[7:0] Interrupt Polarity Wake-up Timer Adjust Bit [2:0] Low-voltage Reset Disable Precision USB Clocking Enable Reserved P2.1 (Int Clk Mode Only VREG Pin State Bit 3 Bit 2 Bit 1 Bit 0 Read/Write/ Both/ BBBBBBBB BBBBBBBB Default/ Reset 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 --RR--RR WWWWWWWW WWWWWWWW WWWWWWWW WWWWWWWW WWWWWWWW WWWWWWWW WWWWWWWW WWWWWWWW ENDPOINT 0, I AND 2 CONFIGURATION 0x10 USB Device Address Device Address Enable SETUP Received STALL Data 0/1 Toggle IN Received OUT Received ACKed Transaction ACKed Transaction Reserved Device Address rN ew D es Internal Clock Output Disable External Oscillator Enable Mode Bit Mode Bit Byte Count D+/D- Forcing Bit 1.024 ms Interrupt Enable EP2 Interrupt Enable 128 s Interrupt Enable EP1 Interrupt Enable USB Bus Reset-PS/2 Activity Intr. Enable EP0 Interrupt Enable Timer Bit [11:8] CPHA SCK Select Capture B Rising Intr Enable Capture B Rising Event Interrupt Enable Sense Capture A Falling Intr Enable Capture A Falling Event Reserved Capture A Rising Intr Enable Capture A Rising Event Run ig 0x12 0x14, 0x16 EP0 Mode EP1, EP2 Mode Register Reserved Data Valid fo 0x1F USBSC USB Status and Control PS/2 Pull-up Enable VREG Enable de INTERRUPT 0x21 Endpoint Interrupt Enable om m 0x20 Global Interrupt Enable Wake-up Interrupt Enable GPIO Interrupt Enable en USB Reset-PS/2 Activity Interrupt Mode d 0x11, EP0,1, and 2 Counter 0x13, and 0x15 Reserved USB Bus Activity Capture Capture Timer B Intr. Timer A Intr. Enable Enable Reserved SPI Interrupt Enable ec TIMER 0x24 0x25 0x60 Timer LSB Timer Bit [7:0] Reserved Data I/O Timer (MSB) SPI Data ot R SPI 0x61 SPI Control TCMP TBF Comm Mode [1:0] CPOL 0x40 0x41 Capture Timer A-Rising, Data Register Capture Timer A-Falling, Data Register Capture A Rising Data Capture A Falling Data Capture B Rising Data Capture B Falling Data First Edge Hold Prescale Bit [2:0] Capture B Falling Intr Enable Capture B Falling Event LVR/BOR Reset Suspend N CAPTURE TIMER 0x42 0x43 0x44 Capture Timer B-Rising, Data Register Capture Timer B-Falling, Data Register Capture Timer Configuration Capture Timer Status 0x45 Reserved Document #: 38-08022 Rev. *D PROC SC. 0xFF Process Status & Control IRQ Pending Watch Dog Reset Bus Interrupt Event ns BBBBBBBB BBBBBBBB BBBBBBBB B--BBBBB BB--BBBB BBB-BBBB BBBBBBBB 00000000 00000000 00000000 00000000 00000000 00000000 -----BBB 00000000 RRRRRRRR 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ----RRRR BBBBBBBB BBBBBBBB RRRRRRRR RRRRRRRR RRRRRRRR RRRRRRRR BBBBBBBB ----BBBB 00000000 RBBBBR-B See Section Page 40 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Absolute Maximum Ratings Storage Temperature ................................. -65C to +150C Ambient Temperature with Power Applied...... -0C to +70C Supply Voltage on VCC Relative to VSS ..........-0.5V to +7.0V DC Input Voltage .................................. -0.5V to +VCC+0.5V Maximum Total Sink Output Current into Port 0 and 1 and Pins70 mA Maximum Total Source Output Current into Port 0 and 1 and Pins30 mA Maximum On-chip Power Dissipation on any GPIO Pin50 mW Power Dissipation..................................................... 300 mW Static Discharge Voltage .......................................... > 2000V Latch-up Current ................................................... > 200 mA DC Voltage Applied to Outputs in High Z State -0.5V to + VCC+0.5V DC Characteristics FOSC = 6 MHz; Operating Temperature = 0 to 70C Parameter General VCC1 VCC2 ICC1 ICC2 ISB1 ISB2 VPP TRSNTR IIL ISNK ISRC Operating Voltage Operating Voltage VCC Operating Supply Current - Internal Oscillator Mode Typical ICC1 = 16 mA[5] VCC Operating Supply Current - External Oscillator Mode Typical ICC2= 13 mA[5] Standby Current - No Wake-up Osc Programming Voltage (disabled) Resonator Start-up Interval Input Leakage Current Standby Current - With Wake-up Osc Note 4 Note 4 Conditions rN ew D es Min. VLVR 4.35 Max. 5.5 5.25 20 Unit V V mA 17 mA 25 75 -0.4 0.4 256 1 70 30 A A V s A mA mA 3.5 4.0 100 V ms 3.0 2.8 3.6 300 3.6 V pF V Page 41 of 53 [+] Feedback VCC = 5.0V. T = Room Temperature m om Max ISS GPIO Sink Current Max ICC GPIO Source Current Low-Voltage and Power-on Reset ec ot R VLVR tVCCS Low-Voltage Reset Trip Voltage VCC Power-on Slew Time USB Interface en de d VCC = 5.5V, no GPIO loading VCC = 5.0V. T = Room Temperature Oscillator off, D- > 2.7V Oscillator off, D- > 2.7V VCC = 5.0V, ceramic resonator Any I/O pin Cumulative across all ports[6] Cumulative across all ports[6] VCC below VLVR for >100 ns[7] linear ramp: 0 to 4V[8] CREG VOHU N VREG VREG Regulator Output Voltage Capacitance on VREG Pin Static Output High, driven Load = RPU +RPD[9, 10] External cap not required RPD to Gnd[4] Notes 4. Full functionality is guaranteed in VCC1 range, except USB transmitter specifications and GPIO output currents are guaranteed for VCC2 range. 5. Bench measurements taken under nominal operating conditions. Spec cannot be guaranteed at final test. 6. Total current cumulative across all Port pins, limited to minimize Power and Ground-Drop noise effects. 7. LVR is automatically disabled during suspend mode. 8. LVR will re-occur whenever VCC drops below VLVR. In suspend or with LVR disabled, BOR occurs whenever VCC drops below approximately 2.5V. 9. VREG specified for regulator enabled, idle conditions (i.e., no USB traffic), with load resistors listed. During USB transmits from the internal SIE, the VREG output is not regulated, and should not be used as a general source of regulated voltage in that case. During receive of USB data, the VREG output drops when D- is LOW due to internal series resistance of approximately 200 at the VREG pin. 10. In suspend mode, VREG is only valid if RPU is connected from D- to VREG pin, and RPD is connected from D- to ground. Document #: 38-08022 Rev. *D fo VCC = 5.5V, no GPIO loading ig ns CY7C63722C CY7C63723C CY7C63743C DC Characteristics FOSC = 6 MHz; Operating Temperature = 0 to 70C (continued) Parameter VOLU VOHZ VDI VCM VSE CIN ILO RPU RPD Static Output Low Static Output High, idle or suspend Differential Input Sensitivity Differential Input Common Mode Range Single Ended Receiver Threshold Transceiver Capacitance Hi-Z State Data Line Leakage External Bus Pull-up resistance (D-) External Bus Pull-down resistance PS/2 Interface VOLP RPS2 Static Output Low Internal PS/2 Pull-up Resistance General Purpose I/O Interface RUP VICR VICF VHC VITTL VOL1A VOL1B VOL2 VOL3 VOH RXIN Pull-up Resistance Input Threshold Voltage, CMOS mode Input Threshold Voltage, CMOS mode Input Hysteresis Voltage, CMOS mode Input Threshold Voltage, TTL mode Output Low Voltage, high drive mode 0 V < Vin<3.3 V (D+ or D- pins) 1.3 k 2% to VREG[11] 15 k 5% to Gnd Conditions With RPU to VREG pin RPD connected D- to Gnd, RPU connected D- to VREG pin[4] |(D+)-(D-)| 2.7 0.2 0.8 0.8 -10 2.5 20 2.0 10 Min. Max. 0.3 3.6 Unit V V V ig 1.274 1.326 15.75 14.25 0.4 3 7 8 40% 35% 3% 0.8 24 60% 55% 10% 2.0 0.8 0.4 0.4 0.4 VCC-2 50 D es SDATA, SCLK pins, PS/2 Enabled rN ew Isink = 5 mA, SDATA or SCLK pins High to low edge, Port 0 or 1 High to low edge, Port 0 or 1 fo Low to high edge, Port 0 or 1 d Ports 0, 1, and 2 1[4] 1[4] de IOL1 = 50 mA, Ports 0 or IOL1 = 25 mA, Ports 0 or Output Low Voltage, low drive mode Pull-down resistance, XTALIN pin en Output Low Voltage, medium drive mode Output High Voltage, strong drive mode IOL2 = 8 mA, Ports 0 or 1[4] IOL3 = 2 mA, Ports 0 or 1[4] mA[4] Port 0 or 1, IOH = 2 m Internal Clock Mode only Note 11. The 200 internal resistance at the VREG pin gives a standard USB pull-up using this value. Alternately, a 1.5 k,5%pull-up from D- to an external 3.3V supply can be used. Document #: 38-08022 Rev. *D N ot R ec om ns V V pF k k A V k k VCC VCC VCC V V V V V V k Page 42 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Switching Characteristics Parameter FICLK FICLK2 Description Internal Clock Mode Internal Clock Frequency Internal Clock Frequency, USB mode External Oscillator Mode Input Clock Cycle Time Clock HIGH Time Clock LOW Time Reset Timing Time-out Delay after LVR/BOR Internal Wake-up Period WatchDog Timer Period USB Driver Characteristics Transition Rise Time Transition Rise Time Transition Fall Time Transition Fall Time Rise/Fall Time Matching Output Signal Crossover Voltage[18] USB Data Timing Low Speed Data Rate Receiver Data Jitter Tolerance Receiver Data Jitter Tolerance Differential to EOP transition Skew EOP Width at Receiver Source EOP Width Differential Driver Jitter Differential Driver Jitter Width of SE0 during Diff. Transition Conditions Internal Clock Mode enabled Internal Clock Mode enabled, Bit 2 of register 0xF8h is set (Precision USB Clocking)[12] USB Operation, with External 1.5% Ceramic Resonator or Crystal Min. 5.7 5.91 Max. 6.3 6.09 Unit MHz MHz TCYC TCH TCL tSTART tWAKE tWATCH TR TR TF TF TRFM VCRS 164.2 0.45 tCYC 0.45 tCYC 24 1 10.1 75 ig 60 5 14.6 300 300 125 2.0 1.5225 75 45 100 1.50 95 150 210 300 2 2.2 D es 75 80 1.3 1.4775 -75 -45 -40 670 1.25 -95 -150 50 ot R TFPS2 Non-USB Mode Driver Characteristics SDATA/SCK Transition Fall Time SPI Timing SPI Master Clock Rate SPI Slave Clock Rate ec TDRATE TDJR1 TDJR2 TDEOP TEOPR2 TEOPT TUDJ1 TUDJ2 TLST om Ave. Bit Rate (1.5 Mb/s 1.5%) To Next Transition[15] For Paired Transitions[15] Note 15 Accepts as EOP[15] To next transition, Figure 46 To paired transition, Figure 46 Note 16 de d CLoad = 200 pF (10% to 90%[4]) CLoad = 600 pF (10% to 90%[4]) CLoad = 200 pF (10% to 90%[4]) CLoad = 600 pF (10% to 90%[4]) tr/tf[4, 14] CLoad = 200 to 600 pF[4] rN ew Enabled Wake-up FOSC = 6 MHz Interrupt[13] fo m en CLoad = 150 pF to 600 pF See Figures 47 to 50[17] FCLK/3; see Figure 20 TSMCK TSSCK N Notes 12. Initially FICLK2 = FICLK until a USB packet is received. 13. Wake-up time for Wake-up Adjust Bits cleared to 000b (minimum setting) 14. Tested at 200 pF. 15. Measured at cross-over point of differential data signals. 16. Non-USB Mode refers to driving the D-/SDATA and/or D+/SCLK pins with the Control Bits of the USB Status and Control Register, with Control Bit 2 HIGH. 17. SPI timing specified for capacitive load of 50 pF, with GPIO output mode = 01 (medium low drive, strong high drive). 18. Per the USB 2.0 Specification, Table 7.7, Note 10, the first transition from the Idle state is excluded. Document #: 38-08022 Rev. *D ns 169.2 ns ns ns ms ms ms ns ns ns ns % V Mb/s ns ns ns ns s ns ns ns ns MHz MHz Page 43 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Switching Characteristics (continued) Parameter TSCKH TSCKL TMDO TMDO1 TMSU TMHD TSSU TSHD TSDO TSDO1 TSSS TSSH Description SPI Clock High Time SPI Clock Low Time Master Data Output Time Master Data Output Time, First bit with CPHA = 1 Master Input Data Set-up time Master Input Data Hold time Slave Input Data Set-up Time Slave Input Data Hold Time Slave Data Output Time Slave Data Output Time, First bit with CPHA = 1 Slave Select Set-up Time Slave Select Hold Time Conditions High for CPOL = 0, Low for CPOL = 1 Low for CPOL = 0, High for CPOL = 1 SCK to data valid Time before leading SCK edge Min. 125 125 -25 100 50 50 50 50 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns 50 SCK to data valid Time after SS LOW to data valid Before first SCK edge After last SCK edge Figure 42. Clock Timing TCH de CLOCK d m en Figure 43. USB Data Signal Timing om Voh D+ TR 90% 90% Vcrs Vol 10% fo TCYC ec D- Document #: 38-08022 Rev. *D N ot R rN ew TCL TF 10% D es 150 150 ig 100 100 ns Page 44 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 44. Receiver Jitter Tolerance TPERIOD Differential Data Lines TJR Consecutive Transitions N * TPERIOD + TJR1 Paired Transitions N * TPERIOD + TJR2 TJR1 TJR2 Figure 45. Differential to EOP Transition Skew and EOP Width TPERIOD Differential Data Lines Crossover Point Crossover Point Extended de Diff. Data to SE0 Skew N * TPERIOD + TDEOP d fo rN ew Source EOP Width: Receiver EOP Width: TEOPR1, TEOPR2 Differential Data Lines ec om ot R m TPERIOD en Figure 46. Differential Data Jitter Crossover Points Consecutive Transitions N * TPERIOD + TxJR1 Paired Transitions N * TPERIOD + TxJR2 Document #: 38-08022 Rev. *D N D es TEOPT ig Page 45 of 53 [+] Feedback ns CY7C63722C CY7C63723C CY7C63743C Figure 47. SPI Master Timing, CPHA = 0 SS (SS is under firmware control in SPI Master mode) SCK (CPOL=0) TSCKL TSCKH SCK (CPOL=1) TMDO MISO MSB rN ew d fo MOSI MSB TMSU TMHD Figure 48. SPI Slave Timing, CPHA = 0 SS TSSS en de D es LSB LSB SCK (CPOL=0) MOSI ot R ec SCK (CPOL=1) om TSCKH m TSCKL MSB N TSDO TSSU TSHD MSB LSB MISO Document #: 38-08022 Rev. *D ig TSSH LSB ns Page 46 of 53 [+] Feedback CY7C63722C CY7C63723C CY7C63743C Figure 49. SPI Master Timing, CPHA = 1 SS (SS is under firmware control in SPI Master mode) TSCKH TMDO1 TMDO MSB MOSI MISO MSB TMSU TMHD Figure 50. SPI Slave Timing, CPHA = 1 SS TSSS en de d fo rN ew LSB D es LSB SCK (CPOL=1) SCK (CPOL=0) TSCKH ot R ec SCK (CPOL=1) MOSI MSB om m TSCKL LSB TSSU TSHD N TSDO1 MSB TSDO LSB MISO Document #: 38-08022 Rev. *D ig TSSH Page 47 of 53 [+] Feedback ns SCK (CPOL=0) TSCKL CY7C63722C CY7C63723C CY7C63743C Ordering Information Ordering Code CY7C63723C-PXC CY7C63723C-SXC CY7C63743C-PXC CY7C63743C-SXC CY7C63743C-QXC CY7C63722C-XC EPROM Size 8 KB 8 KB 8 KB 8 KB 8 KB 8 KB Package Name P3 S3 P13 S13 Q13 - Package Type 18-Pin (300-Mil) Lead-free PDIP 18-Pin Small Outline Lead-free Package 24-Pin (300-Mil) Lead-free PDIP 24-Pin Small Outline Lead-free Package 24-lead QSOP Lead-free Package 25-Pad DIE Form Operating Range Commercial Commercial Commercial Figure 51. 18-Pin PDIP (300-Mil) Molded DIP ec om m en de d fo rN ew 51-85010 *C Document #: 38-08022 Rev. *D N ot R D es Page 48 of 53 [+] Feedback Package Diagrams ig ns Commercial Commercial Commercial CY7C63722C CY7C63723C CY7C63743C Figure 52. 18L SOIC .463 X.300 X .0932 Inches d fo rN ew Figure 53. 24-Pin SOIC (.615 X .300 X .0932 Inches D es N ot R ec om m en de 51-85023 *C 51-85025 *D Document #: 38-08022 Rev. *D ig Page 49 of 53 [+] Feedback ns CY7C63722C CY7C63723C CY7C63743C Figure 54. 24-Pin PDIP 1.260 X .270 X .140 I rN ew N ot R ec om m en de d Figure 55. 24-Pin QSOP 8.65 X 3.9 X 1.44 MM fo Document #: 38-08022 Rev. *D D es 51-85013 *C 51-85055 *C ig Page 50 of 53 [+] Feedback ns CY7C63722C CY7C63723C CY7C63743C Figure 56. Die Form Cypress Logo Die Step: 1907 x 3011 microns Die Size: 1830.8 x 2909 microns Die Thickness: 14 mils = 355.6 microns Pad Size: 80 x 80 microns Y (1907, 3001) 4 5 6 7 8 9 3 2 1 25 24 23 22 21 20 19 18 (0,0) X Table 11. CY7C63722C-XC Probe Pad Coordinates in microns ((0,0) to bond pad centers) Pad Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 17 Pin Name P0.0 P0.1 P0.2 P0.3 P1.0 P1.2 P1.4 Vss Vss P1.6 X (microns) 788.95 597.45 406.00 154.95 154.95 154.95 154.95 154.95 154.95 154.95 363.90 531.70 1066.55 1210.75 1449.75 1662.35 1735.35 1752.05 1752.05 1752.05 1752.05 1752.05 1393.25 1171.80 980.35 Y (microns) 2843.15 2843.15 2843.15 2687.95 2496.45 2305.05 2113.60 1922.05 1730.90 312.50 184.85 184.85 184.85 184.85 184.85 184.85 289.85 1832.75 2024.30 2215.75 2407.15 2598.65 2843.15 2843.15 2843.15 om ec ot R N 19 20 21 22 23 24 25 Document #: 38-08022 Rev. *D m XTALOUT Vcc D- D+ P1.7 P1.5 P1.3 P1.1 P0.7 P0.6 P0.5 P0.4 en Vpp VREG XTALIN de d fo rN ew Table 11 below shows the die pad coordinates for the CY7C63722C-XC. The center location of each bond pad is relative to the bottom left corner of the die which has coordinate (0,0). D es 10 13 14 15 16 11 12 17 ig Page 51 of 53 [+] Feedback ns CY7C63722C CY7C63723C CY7C63743C Document History Page Document Title: CY7C63722C, CY7C63723C, CY7C63743C enCoReTM USB Combination Low-Speed USB and PS/2 Peripheral Controller Document Number: 38-08022 REV. ** ECN NO. 118643 Issue Date 10/22/02 Orig. of Change BON Description of Change Converted from Spec 38-00944 to Spec 38-08022. Added notes 17, 18 to section 26 Removed obsolete parts (63722-PC and 63742) Added die sale Added section 23 (Register Summary) Added 24 QSOP package Added Lead-free packages to section 27 Reformatted to update format *B *C 267229 429169 See ECN See ECN ARI TYJ Corrected part number in the Ordering Information section *D 3057657 10/13/2010 AJHA Added "Not recommended for new designs" watermark in the PDF. Updated package diagrams. Updated template. Document #: 38-08022 Rev. *D N ot R ec om m en de d fo rN ew Updated part numbers with `C' part numbers Changed to `Cypress Perform' logo Added the 24-QSOP part offering D es Page 52 of 53 [+] Feedback *A 243308 SEE ECN KKU ig ns CY7C63722C CY7C63723C CY7C63743C Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/plc cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless PSoC Solutions PSoC 1 | PSoC 3 | PSoC 5 (c) Cypress Semiconductor Corporation, 2004-2010. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 38-08022 Rev. *D N ot R ec om m en de d Revised October 20, 2010 fo rN ew Page 53 of 53 enCoRe is a trademark of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders. D es [+] Feedback ig ns psoc.cypress.com/solutions |
Price & Availability of CY7C63743C-QXC
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |